Can someone explain you how to get reverse thrust on the revers axis of the Hotas Warthog throttle?  I had it working in FSlabs but I can't figure it out in MSFS with the FBW320.  Thanks!

Set the detents  via the EBC, and configure  a button  in the MSFS  controls set up to activate reverse thrust.

18 minutes ago, Car147 said:

Set the detents  via the EBC, and configure  a button  in the MSFS  controls set up to activate reverse thrust.

That sounds like you mean to assign a button.  I’m referring to the reverse axis where you can move the thrust lever under the idle position. 

43 minutes ago, Zimmerbz said:

That sounds like you mean to assign a button.  I’m referring to the reverse axis where you can move the thrust lever under the idle position. 

Yup, it was the only way i could get it to work. I don't know whether it is possible through the EBC, and tried a few times without success.

IN MSFS for Throttle Warthog:

STEP 1

THROTTLE 1 AXIS is assigned to JOYSTICK AXE DZ and THROTTLE 2 AXIS IS ASSIGNED TO JOYSTICK AXE GZ 

For both axes Throttle 1 and 2 i have checked the box inverted axes

STEP 2
Assign the lifting reversers detents on the levers to THROTTLE 1 DECREASE BUTTON 29 and THROTTLE 2 DECREASE BUTTON 30

IN FBW A32NX EFB

Uncheck Reverser on axis (Off position is white)

Check Independant axis (On position is green)

Calibrate normally both throttle levers left and right idle to idle position which is 0 on the pedestral throttle, repeat for CLB, FLEX, TO/GA positions.

That's all it should works perfectly after that.

The only thing is when you land and engage the reverse (by pulling the levers upwards when in IDLE then pulling backwards into the reverser section), if you want to stop the reverse return the levers to iddle position and move them a little forward to disengage the reverse.

1 hour ago, Zimmerbz said:

Can someone explain you how to get reverse thrust on the revers axis of the Hotas Warthog throttle?  I had it working in FSlabs but I can't figure it out in MSFS with the FBW320.  Thanks!

Setup the throttles using the FBW setup in the EFB, DO NOT setup reverse at this point, set both throttles to the bottom, now follow the instructions below.

I use button 15 on the TM Warthog throttle which works perfectly on the A32NX. Don't use toggle, choose hold. As you land to retard the throttles squeeze the red button (15) and push the throttles to low, medium or full retard, once you hit 70 knts or below, still holding the red button in, pull the throttles back then release (the button). If you don't do this you will set off an alarm. You can use toggle, but I now prefer hold.

 

Edited January 31, 20224 yr by SierraHotel

54 minutes ago, Jedi928 said:

IN MSFS for Throttle Warthog:

STEP 1

THROTTLE 1 AXIS is assigned to JOYSTICK AXE DZ and THROTTLE 2 AXIS IS ASSIGNED TO JOYSTICK AXE GZ 

For both axes Throttle 1 and 2 i have checked the box inverted axes

STEP 2
Assign the lifting reversers detents on the levers to THROTTLE 1 DECREASE BUTTON 29 and THROTTLE 2 DECREASE BUTTON 30

IN FBW A32NX EFB

Uncheck Reverser on axis (Off position is white)

Check Independant axis (On position is green)

Calibrate normally both throttle levers left and right idle to idle position which is 0 on the pedestral throttle, repeat for CLB, FLEX, TO/GA positions.

That's all it should works perfectly after that.

The only thing is when you land and engage the reverse (by pulling the levers upwards when in IDLE then pulling backwards into the reverser section), if you want to stop the reverse return the levers to iddle position and move them a little forward to disengage the reverse.

Thanks for the detailed instructions, as i said earlier i could not get it to work and ended up using the settings i had. I will certainly be changing my set up now i know what to do.

Cheer's

On 1/31/2022 at 1:10 PM, Jedi928 said:

IN MSFS for Throttle Warthog:

STEP 1

THROTTLE 1 AXIS is assigned to JOYSTICK AXE DZ and THROTTLE 2 AXIS IS ASSIGNED TO JOYSTICK AXE GZ 

For both axes Throttle 1 and 2 i have checked the box inverted axes

STEP 2
Assign the lifting reversers detents on the levers to THROTTLE 1 DECREASE BUTTON 29 and THROTTLE 2 DECREASE BUTTON 30

IN FBW A32NX EFB

Uncheck Reverser on axis (Off position is white)

Check Independant axis (On position is green)

Calibrate normally both throttle levers left and right idle to idle position which is 0 on the pedestral throttle, repeat for CLB, FLEX, TO/GA positions.

That's all it should works perfectly after that.

The only thing is when you land and engage the reverse (by pulling the levers upwards when in IDLE then pulling backwards into the reverser section), if you want to stop the reverse return the levers to iddle position and move them a little forward to disengage the reverse.

I was messing around with a few things and now when I press the throttle forward, it reduces the position of the thrust lever, and when I cut, i go full forward.  Basically it is opposite.  I've tried checking and unchecking reverse axis and I can't figure it out.  

I have Throttle 2 Axis mapped to Joystick L - Axis Y and Throttle Axis 1 Joystick L - Axis X.  Any thoughts?>