crisu19

I have created a user.lua with several extensions: user.lua Maybe you can reuse it or put it into the next version. Best regards, Christian

Thanks for the module, very much appreciated! The function FNX_OVHD_AICE_ENG1_*() exists twice. In FNX_OVHD_AICE_WING_on() Lvar "L:S_OH_PNEUMATIC_ENG1_ANTI_ICE" is used. I obseved, that packs, bleed, hdy pumps, brake fan, EFIX Buttons (WPT, CSTR, etc.) do not exist in the module. Will they be added in future? Best regards, Christian

Great, thanks a lot for your quick reply.

Hello, I am using Linda 3.2.6. When I am selecting "Developer Mode" in "Setup Linda" the "Linda Tracer" and Linda Editor" activates. But if I klick another Windows and then back to Linda, the "Developer Mode" deactivates automatically. Even "Linda Logging" setting in "Linda Console" behaves the same, setting is gone when leaving window. The setting is stored in "linda-gui.ini", but when it automatically deactivated, this deactivation is synced to confilg file. I also tried to activate Dev-Mode via direct entry to config file, but it is immediately overwritten. Linda did not behave like this in previous versions is used. Is there a way to activate Dev-Mode and Log-Levels permanent? Thanks and best regards, Christian

That's really great and highly appreciated, thanks a lot and happy easter, Christian

I found out, that the set speed is stored in "CM1_ASI_needle3", but I had no success with the other. Christian

Many thanks for the great new Module. It works really fine. Is there a way to control the following switches, buttons and selectors: ENG Gen 1 & Gen 2 CG Dialer / TO Flaps Dialer on pedestal TARA switch abv/norm/below Clock/Timer (RUN/HLD/RST) TERR Button on F/O main panel AC Volt / Frequ/DC Volt Bus Selector to control volt/amp meter on the Elec overhead panel Did I understood you right, that there are no LVars, Offsets or other variable where I can read current set SPD, HDG, ALT and VS? Thanks and best regards, Christian

Thanks for trying to repo my issue. I'll check the power management. But to be honest, the Radio panel worked really well with SPAD 0.5.1, but SPAD does no longer work with P3D v4. I just tried SPAD.neXt which is working fine with the Radio panel. I am using LINDA and LUA with my self made SIM Panels and it's working really well. I have now moved to version 3.0.5 without any issue. You guy's did a great job with LINDA! https://www.dropbox.com/s/ktyplhfhe7jubi5/IMG_6505.jpg Thanks and best regards, Christian

Thanks for the hint. The new log files can be found here: FSUIPC5.log https://www.dropbox.com/s/xmgh6f7et7grwkk/FSUIPC5.log?dl=0 linda2.log https://www.dropbox.com/s/w29ae2iavd5e7p4/linda2.log?dl=0 Thanks in advance, Christian

I am testing with the Default Mooney Bravo and Beech Baron. Logfile can be found here: https://www.dropbox.com/s/xmgh6f7et7grwkk/FSUIPC5.log?dl=0 Thanks a lot, Christian

Thanks for your really quick reply! In LUA Mode it works fine. But in GUI Mode (configured as described) I am getting the dashed-line, then pressing e.g. the ACT/STBY button and the display stays black for COMs, NAVs, ADF. Only QNH is display by selecting XPDR, but also now Squawk is displayed in this mode. The GUI log with DEBUG level does not show any entry by pressing Radio panel buttons. Is there a way to check what's going wrong? Thanks, Christian

I would like to tryout the LINDA GUI function for my Saitek Radio panel instead the old SPAD tools. For SPAD I must not install any Saitek drivers. Do I need to install Saitek drivers to use my Radio panel with LINDA? I only get the QNH displayed when switching to XPDR, but there is no COM, NAV frequency displayed. I am using P3D v4.1, LINDA 3.0.5 and FSUIPC 5.122 BR, Christian

Depending on the aircraft I am flying I am using a yoke or joystick. Every time I change the control device, I have to change the assignment of Tilt/Pan under Control Assignments. Is there a way to get rid of these reassignments? Does Chase Plane support more than one control device? Christian

Hello, I have already checked for driver updates using windows default function check for drivers updates. The drivers from 2006 are the latest provided by microsoft. FSUIPC is clean in terms of key assignments. I can reproduce the issue by just checking the key switches using windows default game controler panel without any FS related software. I have checked the behaviour as well with another pc and got the same problem. It seems to be related to the VR TT panel hardware or HID drivers. I have not tried with other OS than Windows 7. So I guess I have to live with it. Thanks, Christian

Thanks for your reply. I have tried several USB ports (USB2 and USB3) of my new ASUS Z97 Pro Gamer board. But in general there was no difference. In terms of the driver there was no need to install any driver. The VR TT panel is recognized as default HID joystick device with Windows 7 default drivers. Since there in no need for separate drivers, VR does not provide any driver up-to-date for this panel. Just checked the currently installed HID Game Controller driver: Provider: Microsoft Date: 21.06.2006 Version: 6.1.7601.18199 I have found newer drivers here: http://www.driverscape.com/download/hid-compliant-game-controller Description: HID-compliant game controller Driver Installer File Version: 8.4 File Size: 2.33M Supported OS: Windows 8, Windows 7, Windows Vista, Windows XP I don't know driverscape. Are drivers provided by driverscape trustworthy? What are the best drivers to be used? Thanks and best regards, Christian