aaronavtr

Scandi did you solve your sound issue? I had the same thing happen to me today. I was in mid flight and out of no where, the sounds of FS2crew stopped all together. The FO did respond to my commands but he never responded. Neither did the FA's, however ALL the other sound in FS9 and rc4 continued like nothing happened.

Did it work for you?

No, I was in the climbing phase of flight and had given a command (I think it was flaps up) which he responded to. I was hand flying it at the time and speaking into the mic so I couldn't have put HM on. Then when I gave him a heading to put into the mcp (this is after command A was already engaged; which the FO engaged by the way) there was nothing, zip, nada.I love this software so much, I just hope I can get this issue resolved. I'll keep trying.

So I've given it a few attempts and for the most part, the FO has been quite good. However I was just in mid flight and the FO stopped responding to me. I gave him a heading to put into the MCP and he didn't do it. I gave him an altitude command (all according to how it should be pronounced in the manual and still nothing).It appears as though my FO works when it wants and doesn't when he wants to. I've already reinstalled the product already. Any other ideas? Perhaps an update :(

I have the the green bar showing so I'll test it and report back.

Copy that on unplugging the usb device.I haven't really messed with the "green bar" feature on FS2crew but will mess with it. My microphone doesn't have a mute feature. During the cruise phase of flight I usually just put the HM option on until I'm ready to commence the descent task.In addition to the microphone, I've also done a whole lot more voice trainings and I am about to reinstall the fs2crew vc on my pc so hopefully my next post will have different results.

OK I guess I was wrong. As previously mentioned I now have a usb headset but for some reason I still have the same problems. On the cfg part of the fs2crew panel, the headset is showing (logitec usb headset) and on today's imparticular flight ALL went smoothly until I began my takeoff roll and climbed off the runway. I then commanded "GEAR UP" and it was as if the FO had left the cockpit because there was NO RESPONSE. The FO had responded to EVERYTHING up til that point including the preflight, before start, before taxi, and other checklist and commands. Not only had he been responding but the FA and ground crew were also flawless. DO NOTE, I WAS IN THE PROPER MODE BEFORE ISSUING THE COMMANDS.As I continued to climb I kept commanding "GEAR UP" but got nothing so I then switched to the After T/O mode and commanded the After T/O checklist....not a peep. I tried other commands while climbing and still...not a peep. Yesterday I was successful in a full flight in which the FO was flawless and responded to EVERYTHING and up til this flight I hadn't changed ANY of the settings be it in the xp sound options or fs2crew panel.To top it off, I then unplugged my usb headset from the computer and then the the whole FS9 shuts down and closes!!!! Perplexed, I then loaded fs2crew vc for my level d and tried it also and without fail when I responded with "ANY SNAGS WITH THE PLANE"...not a peep so I then unplugged the usb cord and yes you guessed it...the whole FS9 shuts down. I then attempted to use other usb ports and got the same result.Any Suggestions?

The mode was actually correct. I have the 'printed' ifly fs2crew flow sheet/manual where I practically read all of my commands from and without fail I am in the right one. HOWEVER...I breezed through the website and noticed that the usb headset was "recommended" and my headset is analog (pink and green plug in's) so I went to the store and purchased a usb headset, plugged it in and what do you know. My commands were completely responded to.Thanks you two for your help anyway.

This has happened a couple of times now. When I begin a flight, I am able to breeze through the preflight checklist, before start checklist, taxi checklist etc. However when I say 'runway entry procedure' I get NO RESPONSE what's so ever. My mic is fine and I've checked the panel to ensure the FO isn't going through any other flows (which it isn't) but for some odd reason he won't repsond whatsoever. I then try to skip that part and go to the 'takeoff' announcement but I get the same result...nothing.Any advice.

Not too sure if that'll work but nothing beats a try. I'll report back. According to the forums at the IFLY website, others are having the exact same issue.

I just tested v1.4 and got the same result. This time it occured when I was beginning my takeoff roll and gave my FO the command that I was going to commence the TO roll. Before I installed v1.4, I thoroughly uninstalled v1.3, and yet FS9 is still crashing. I've never owned FS2crew for any other aircraft as this is my first and I've been able to use it successfully however as of recent, it has started to cause my FS9 to crash, any suggestions???

Consistently...the last several attempted flights, the flight attendant would come to notify me that the boarding was complete. I would then press Shift + | (thats what I have for my secondary button) and then fs9 would simply close. No error message or anything. It'd simply just close!!! The other day it happened again when I was going through the pre-taxi checklist, I was in the middle of it and when I pressed my primary command button to respond, fs9 simply closed again.My buttons are not coupled with any other commands in fs9 and this has only began happening since I installed v1.3. I'm downloading v1.4 now so hopefully that would mediate my problem but I am not too sure. I'll report back.

Hey all...I have been trying to integrate the Reality XP WX500 weather radar into my pmdg 737-700 aircraft. From looking at post and screenshots, many have pulled off the merge and a handfull (including me), have yet to be successfull at it.I am curious to know if anyone here has merged the two and if so...how??? I followed the how to steps from a website (see link below) which include screenshots however after following these steps very closely, I still cannot merge the two. Any help is appreciated.Screenshots and Steps: http://www.mythicalireland.com/other/plane...ather-radar.php

Hey all...I am new to fs2crew and tried a flight not too long ago on the pmdg 737. I wanted to see what it was like to have the first officer execute the precision approached, so I followed the instructions on how to do so. All went well but right over the landing threshold, the FO aborts the landing a goes around. I had given him no command to do so, runway was clear, so what in the world did I do wrong????