rhalton

I have posted the following under downloads PMDG 747 module but have had no replies. I would really like to get flying again with this aircraft. I am revisiting this aircraft after a break and am using mcp2 with Linda 2.5.7 and module 1.2. I still can not get it to work and am getting the error messages error loading module linda-cfg/aircrafts/pmdg 744-400/config-mcp2 from file C:\fsx\modules\linda-cfg/aircrafts/pmdg 744-400/config-mcp2.lua The folder linda-cfg/aircrafts/pmdg 744-400 contains the files config-mcp, config-mcp2, config-mcp2-1505061504, config-mcp2a and config-user The linda console then shows fsx/modules/linda-cfg/aircrafts/pmdg 744-400/config-mcp2.lua:573: '<name>' expected near '}' Can anybody tell me whats wrong Thanks, Richard Halton.

Bad news. Problem is back again for me. Have not changed anything since yesterday. Richard

Hi Scott, Have done a clean re-install of linda 2.5.7 and A2A c172 1.0.3. Everything now works OK - no console errors. Thanks to you and Wayne for your work on this. Richard

Thanks for all your work everybody. I will try a re-install as Scott suggested in the next couple of days and report back Richard

Am using FSX, MCP2, Linda 2.5.7 and A2A Cessna 172 module 1.0.2 Using the heading knob on the MCP2 causes the heading bug on the aircraft to jump about and the MCP reading for the heading does not sync with the aircraft heading. I have tried reassigning the heading knob values in Linda from the A2A library to the FSX control values - heading bug inc and dec. This gives a smooth operation of the heading bug butt he values still do not sync. Can anybody with the A2A 172 help please? Richard Halton

I have had a very stable system and been getting good results flying the Ifly 737 with the MCP Combo 2 for some time. I normally take off with autopilot heading selected and switch to lnav at 1000' approx. and everyting works OK. Today I have tried to set up the aircraft to take off and track a VOR course. I dial in the VOR freq. and then set the course with the MCP course knob but the course reading just runs away with itself and cannot be stopped. If I set the course with the mouse on the course knob on the screen everything is OK.Anybody any ideas? Richard Halton

Have sorted this now. Needed to increase the water effects in FSX.

I have two throttle quadrants attached to my yoke. When tested with fsuipc, throttle 1 shows full movement with axis X Y and Z but quadrant 2 only has full movement for axis Z. X and Y are acting as an on/off switch. I am trying to calibrate the two quadrants for the King Air B200 with two throttle controls, two prop condition controls and two mixture controls. Can anybody help? Thanks, Richard Halton

Have just downloaded the latest N California scenery and latest libraries, and the water in the San Francisco Bay area is brown but the main Pacific is blue. Can anybody tell me what I have done wrong. Thanks, Richard Halton

Thanks Mark. Will check those points.

Have just come back to this problem after viewing all the posts. I am also using Linda and the mcp11 panel but have just tried without linda and the panel, and the problem still persists.

Have downloaded the older version of UT2Bridge and still get the same error.

I am on my first day of a version 6.20 trial and am having problems with the UT bridge. I have downloaded it and tried to run it from its folder prog files/internal workings/voxatc and I am getting a ut bridge error, ut2 not found. I have ut2 installed in my main fsx folder which is C:/FSX.Can anybody help please.

Loaded a flight today and fault has returned. Re-connected to sound blaster, removed driver and installed original driver. Fault still there. Any more ideas? Thanks

Have disabled the sound blaster card and ran the sound through the on-board sound card. Now works perfectly. Thanks for your help