773Adas

Thanks, for response. I did both SAARU and ADIRU failure which explanins HDG entry. I will do some testing on this elevetor control and see how it behaves.

Hi, everyone Recently, just for fun I've done ADIRU/SAARU failure in my B777F and I was going trough abnormal checklist and I stopped at the point where according to procedure I had to enter heading into POS INT p.1 in the space which should be created in the FMS, but it didn't happen. Are there any extra conditions to be met enabling HDG entrance in POS INT page? Another symptom that I got after ADIRU/SAARU failure is that I lost elevetor control. It ceased to respond from control column movments comands, which visually moved in the cockpit, only trim was working, but after some time it also stopped to react. Only altn trim seemed to remain operational, but I didn't have key assinged to it so I crashed :(. Is this something normal to observe when this failure occures or this is something which shouldn't happen? Thanks, Adam Omieljanowicz

Hi I have created a ticket in PMDG support, it is under investigation. Adam Omieljanowicz

I always run it as admin. I switched off firewall and anti virus but still, Ops Center doesn't see 737ngx. Adam Omieljanowicz

Do I have to remove whole Ops Center or only files which refer to 737ngx? Adam Omieljanowicz Just did all, and still nothing (I have removed filies which refer to 737 only) Adam Omieljanowicz

I have reinstalled NGX and followed all items in procedure and it hasn't helped. Ops Center still doesn't recognise that I have 737ngx installed. Adam Omieljanowicz

No, I didn't I will do it as soon as possible, and write about the effect.

Hi! I have installed the newest version of OC (at least there is no information about any updates) and my 737ngx for FSX module seems to disappear, I cannot get any options available (liveries, documentation, etc.). I have also 777 for FSX and P3D and they seem to work properly. I have updated 737 to the newest sp1d version. Any Ideas? Adam Omieljanowicz

Hi! I have a question about PMDG 777, to be more specific about B777F aircraft type. After installing SP1 I've noticed that suprnmry oxygen switch on overhead panel became unavailable. In case of 777 passenger version it is there and it is serviceable. Is it some source of error I am facing or it has been intentionally done? Thanks for help. Regards, Adam

Hi, It wasn't my purpose I think it is because I had error msg from website that my topic has failed and wasn't posted but as I see thoose msgs weren't true and actually topic was posted. Sorry for that

Hi, I have a small problem with my 777, when I save a flight after landing and load it up again ADIRU is not aligned and my FSX seemed to crashed few times shortly after loading up saved flight. This only happens while the aircraft stands on the ground, in flight the problem seems to not exist. Any ideas? Thanks, Adam

Hi, I have a small problem with my 777, when I save a flight after landing and load it up again ADIRU is not aligned and my FSX seemed to crashed few times shortly after loading up saved flight. This only happens while the aircraft stands on the ground, in flight the problem seems to not exist. Any ideas? Thanks, Adam

Hi, I have a small problem with my 777, when I save a flight after landing and load it up again ADIRU is not aligned and my FSX seemed to crashed few times shortly after loading up saved flight. This only happens while the aircraft stands on the ground, in flight the problem seems to not exist. Any ideas? Thanks, Adam

Hi, I have a small problem with my 777, when I save a flight after landing and load it up again ADIRU is not aligned and my FSX seemed to crashed few times shortly after loading up saved flight. This only happens while the aircraft stands on the ground, in flight the problem seems to not exist. Any ideas? Thanks, Adam

Hi, I have a small problem with my 777, when I save a flight after landing and load it up again ADIRU is not aligned and my FSX seemed to crashed few times shortly after loading up saved flight. This only happens while the aircraft stands on the ground, in flight the problem seems to not exist. Any ideas? Thanks, Adam