August 17, 201114 yr Hi, In the 2d Cockpit View, how can I assign a key command for the seat PITCH adjustment, if any ? I've tried the default assignement from FSX, but that doesnt seem to work. The reason, is on final approach, the runway is not visible until after "touchdown". i/e Being on proper glidepath - Established. Also, the F/D bars are not visible on the PFD, Until a ROLL/PITCH mode is selected on or after take-off roll. Was just wondering, cause the F/D bars should show up the moment its switch to ON. ( On ground ) Finally, After probably doing a flight with the -900ngx, and coming back to the select a flight page, to change aircraft to the -800ngx, there are frequent CTD, saying ran out of memory. I've installed the HOTFIX, as well, hoping for a solution.. Anyone else having the same issues ? Thanks in advance. Alienware M17X R3 i7-2860QM 2.5GHz ( 3.6 Ghz TurboBoost 8Mb Cache ) 8GB 1333Mhz DDR3 SDRAM ( 2 x 4GB) 750GB 7200 RPM Hard Drive 2GB GDDR5 Nvidia Gefore GTX 580M Windows 7 Home Premium 64 Bit Mark Knowles First Officer - Boeing 737NG
August 17, 201114 yr Hi, In the 2d Cockpit View, how can I assign a key command for the seat PITCH adjustment, if any ? I've tried the default assignement from FSX, but that doesnt seem to work. The reason, is on final approach, the runway is not visible until after "touchdown". i/e Being on proper glidepath - Established. Also, the F/D bars are not visible on the PFD, Until a ROLL/PITCH mode is selected on or after take-off roll. Was just wondering, cause the F/D bars should show up the moment its switch to ON. ( On ground ) Finally, After probably doing a flight with the -900ngx, and coming back to the select a flight page, to change aircraft to the -800ngx, there are frequent CTD, saying ran out of memory. I've installed the HOTFIX, as well, hoping for a solution.. Anyone else having the same issues ? Thanks in advance.The 2D panel view problem is a well known FSX problem.Shift+Enter normally raises your eye point but I find that it no longer works for me in Win 7. Having no FD bars on the ground is correct on an NG.They will appear during takeoff if they are turned on. Fred. Frederic Steiner.
August 17, 201114 yr CRTL + Q puts the view point down in the 2D panel. Ross Thomson. Intel i7 @ 4.2 Ghz | 10GB DDR3 Corsair | GTX 460 | 600W OCZ | Windows 7 Ultimate 64x. Email me
August 17, 201114 yr Author The 2D panel view problem is a well known FSX problem.Shift+Enter normally raises your eye point but I find that it no longer works for me in Win 7. Having no FD bars on the ground is correct on an NG.They will appear during takeoff if they are turned on. Fred. No, F/D commands on take off roll even if they are turned on. How do you activate the TO/GA ? or to set up a keyboard command for the TO/GA switches to activate on take off roll. I have a keyboard command setup on the fsx default commands, but doesnt seem to work. I pressume, once i hit TO/GA, the F/D bars should come up automatically ?CRTL + Q puts the view point down in the 2D panel. That works, and how Do i put the view point UP ? Alienware M17X R3 i7-2860QM 2.5GHz ( 3.6 Ghz TurboBoost 8Mb Cache ) 8GB 1333Mhz DDR3 SDRAM ( 2 x 4GB) 750GB 7200 RPM Hard Drive 2GB GDDR5 Nvidia Gefore GTX 580M Windows 7 Home Premium 64 Bit Mark Knowles First Officer - Boeing 737NG
August 17, 201114 yr No, F/D commands on take off roll even if they are turned on. How do you activate the TO/GA ? or to set up a keyboard command for the TO/GA switches to activate on take off roll. I have a keyboard command setup on the fsx default commands, but doesnt seem to work. I pressume, once i hit TO/GA, the F/D bars should come up automatically ? That works, and how Do i put the view point UP ?There is a click spot for TOGA near the bottom left screw of the MCP ! That should give you FD bars if they are on. Frederic Steiner.
August 17, 201114 yr there`s a list of keyboard commands available from inside fsx with the option to print them off. ray wed
Create an account or sign in to comment