Jump to content

Archived

This topic is now archived and is closed to further replies.

DOGANG KIM

Question) How to change from FAC,G/P mode to VOR/LOC, G/S mode.

Recommended Posts

I planed to use FAC and G/P mode to land. And FAC and G/P mode was activated. But I thought my condition is not good, so I did try to change the mode to LAND3 mode (VOR/LOC, G/S) for full auto land. And I did input correct ILS FRQ and I clicked the VOR/LOC button on MCP pannel. But nothing chagnes. Still FAC G/P mode was activated, and at 500 feet I manualy controled my airplane and landed. Sorry my poor English. FAC G/P -----------> VOR/LOC G/S how? :) Thank you for watching my question.

Share this post


Link to post
Share on other sites

To get both VOR/LOC and G/S, you need to hit the APP button. I can't remember if the modes can be switched once they're active but try the APP button instead. Also, am I correct in assuming you had the F/D 1 as the master and you put the ILS in on the #1 Nav Radio?

Share this post


Link to post
Share on other sites
To get both VOR/LOC and G/S, you need to hit the APP button. I can't remember if the modes can be switched once they're active but try the APP button instead. Also, am I correct in assuming you had the F/D 1 as the master and you put the ILS in on the #1 Nav Radio?
FAC and G/P was activated, and then I did input correct ILS FRQ to both NAV radio, and both F/D was on. I heared moss signal. And I did click VOR/LOC button and APP button too. But nothing changed. I think maybe.. once FAC and G/P are activated, the system can't be change to another mode. Sorry my poor English.

Share this post


Link to post
Share on other sites

When the ILS is captured (Localizer and Glideslope) the Autopilot goes in a single channel approach with one Autopilot engaged or dual land approach from 1500 ft AGL with a second A/P engage the light on the MCP APP button will go out. If this light is out it's not possible to changeover from APP to VOR/LOC mode or to any other A/P mode. If you want to change you have to disconnect the A/P and make a go-around or land manually. If mode light on MCP mode P/B are lit you can change. if they are not lit anymore you can not change. It's also not possible to engage the VOR/LOC and APP mode at the same time You want to engage APP when to make a dual land approach and engage the second A/P. VOR/LOC mode only capture's the ILS localizer not the Glideslope.

Share this post


Link to post
Share on other sites
When the ILS is captured (Localizer and Glideslope) the Autopilot goes in a single channel approach with one Autopilot engaged or dual land approach from 1500 ft AGL with a second A/P engage the light on the MCP APP button will go out. If this light is out it's not possible to changeover from APP to VOR/LOC mode or to any other A/P mode. If you want to change you have to disconnect the A/P and make a go-around or land manually. If mode light on MCP mode P/B are lit you can change. if they are not lit anymore you can not change. It's also not possible to engage the VOR/LOC and APP mode at the same time You want to engage APP when to make a dual land approach and engage the second A/P. VOR/LOC mode only capture's the ILS localizer not the Glideslope.
I believe you can cancel your approach mode by turning the FDs off and back on again.

Share this post


Link to post
Share on other sites

No, the F/D (Flight Director) switch's just shows the F/D bars on the PFD. When the Flight Director switch's are OFF the F/D bars indication will be removed from the PFD, when the F/D switch's are ON the F/D bars will show again on the PFD. You can also make a dual land approach with F/D switch's in OFF.

Share this post


Link to post
Share on other sites

×
×
  • Create New...