alean

Problem with LINDA 3.0.5 A320X Flightsimlabs

Recommended Posts

Hi guys, initially, everything was working correctly, only now that it's always the fault, that the commands are deactivated alternately, forcing me to reconfigure constantly, I wanted to know, is a problem of exclusion from anti-virus? I await your directions, thank you.

Share this post


Link to post
Share on other sites
Help AVSIM continue to serve you!
Please donate today!

Hi alean 

I fly with the A320X, P3Dv4.1 and LINDA 3.0.5 almost daily. I have experienced no such problems as you describe. I have no AV software running on my exclusive-use FltSim PC due to issues with false positives with other flt sim software. 

Share this post


Link to post
Share on other sites

Hello guys,
I would like to start from the beginning since the installation, because I continue to have the same problem, after the configuration all the commands work, then the defect starts, that some work and some do not, and then all no longer work;
in the screenshot, I would like to know, should I paste the contents of both MACOSX and LINDA _3_0_5_STANDARD V1 folders into the modules folder of the prear3d V4 simulator?

Share this post


Link to post
Share on other sites
9 hours ago, alean said:

Hello guys,
I would like to start from the beginning since the installation, because I continue to have the same problem, after the configuration all the commands work, then the defect starts, that some work and some do not, and then all no longer work;
in the screenshot, I would like to know, should I paste the contents of both MACOSX and LINDA _3_0_5_STANDARD V1 folders into the modules folder of the prear3d V4 simulator?

Hi alean

First of all you can ignore the MACOSX folder (should be hidden). I use my Mac to prepare all downloads and it is possible to end up with some hidden MacOS artefacts which have no adverse effect on a PC.

Secondly, it is the only the /modules and /sound folders within the download that should be copied to the Flt Sim root directory (eg. C:/P3D/). This will copy all the relevant files into the correct /modules and /sounds directories. This is detailed in Release Notes included with LINDA download. Alternatively, if you already have LINDA 3.x.x installed you can use the Maintenance tab to select the download source and install in automatically. The same process is required for each aircraft module.

Finally, I did try ChasePlane but found it conflicted with my existing views so I removed it.

Share this post


Link to post
Share on other sites

If I remove CheasePlane how do I make windows in the cockpit? is there any alternative to suggest?

Share this post


Link to post
Share on other sites

As you did before. The normal Flt Sim windows are available by selecting right-click, cockpit and your required view. I can only answer LINDA queries not general usage ones.

Share this post


Link to post
Share on other sites

Hello guys,
I have a new problem with LINDA on A320 Flightsimlabs;
when I start a flight, everything works correctly;
after starting the descent, at feet 10000, when I have to turn on the landing lights, no commands work anymore, and the LINDA window appears all white to me, what can the poblema be?

Share this post


Link to post
Share on other sites

How are you operating the landing lights? The defined function VC_OVHD_EXTLT_LL_Both_toggle() works for me.

If the problem remains, please follow the Fault Diagnosis procedure and email me the fsuipc5.log and linda2.log.

Share this post


Link to post
Share on other sites

For the lights of the landing, I use: 

ON PRESS:    VC OVHD EXTLT LAND L ON 

ON RELEASE: VC OVHD EXTLT LAND L RETR

ON PRESS    VC OVHD EXTLT LAND R ON

 ON RELEASE: VC OVHD EXTLT LAND R RETR

The problem is that only the landing lights do not work, no commands work anymore, when they are approaching;

 

Share this post


Link to post
Share on other sites

I can see from your previous screenshot that something is not working. Again I need you to follow the Fault Diagnosis thread and email the logs. 

Share this post


Link to post
Share on other sites

I've just sent you the mail with the files; how do you send the screenshot on the forum in the easiest way?

Share this post


Link to post
Share on other sites

Thank you for the logs. There is a problem with FSUIPC5 continually restarting. I suggest you download and install the latest version 5.123c. 

Additionally, you have not turned on any LINDA logging. Please read the thread link above. You need to select Developer mode (under LINDA Settings) and select at least VERBOSE logging. Please resend the logs once you have done that  

 

Share this post


Link to post
Share on other sites

Hello sorry, I suggest you download the latest version of FSUIPC 5? if so, where should I download it from?

Share this post


Link to post
Share on other sites

Hi

Thank you for sending the log files and screen shoots of the LINDA error message. Something is causing LINDA GUI to crash but the 2 error addresses you sent are not consistent. The LINDA LUA code in the logs you sent are working correctly and not reporting any problems.

I would like to pin down the cause before going a further. I have LINDA 3.0.5 working with the FSLabs A320X and my VRi MCP Combo Airbus panel. The functions are working on my setup. You are using several devices which I am unfamiliar with. What is the USB Pad (VID 0417/PID 0130). Is it a touch screen? These are known to cause problems with LINDA operation. Can you try disconnecting this and retesting?

You also have 2 Opencockpits devices (VID 04D8 PID 0000). How are this reported in Setup Joysticks? Do they have unique serial numbers? Again can you try disconnecting these and retesting? You can leave the standard joystick devices connected (Site Pedals, HOTAS, etc).

Share this post


Link to post
Share on other sites

Good afternoon,
the PAD USB, is the VRinsight Tack and Toggle, the two Opencockpit products, they are a Tiller and a Landing gear, they have an electronic card each;
I do not know if they are configured correctly, maybe if you can suggest the configuration;
I tried to disconnect them, but the VRinsight switches and the Throttle switches, sometimes do not work constantly, in the sense that they are always disconnected, ON and not OFF and vice versa, so I always have to intervene to reconfigure the input.

 

26350659548_c7045df3c0_k.jpgScreenshot (159) by Alessandro Anile, su Flickr

26350510528_e6aad7ed88_k.jpgScreenshot (158) by Alessandro Anile, su Flickr

40190508072_7396bec19e.jpg20140924064935cont2 by Alessandro Anile, su Flickr

40223264421_2fccd65099_z.jpgvolantea320 by Alessandro Anile, su Flickr

39325620345_36c6987fec.jpgtrena320 by Alessandro Anile, su Flickr

25352377587_7610d02b54_m.jpgUSB_Axes_pequena by Alessandro Anile, su Flickr

 

 

 

 

Share this post


Link to post
Share on other sites

Thank you for the photos. The VRi switch panel should work similarly to the Saitek one I have. What drivers have you got installed to operate the VRi panel? Apart from the Serial USB drivers, no other VRi software should be running. The other 2 devices should not be an issue but I suggest running a test without these connected so we can isolate the cause of your problems.

I have been testing my FSLabs A320X with the Landing Light ON/OFF function both on the ground and in the air without any issues. I am unable to reproduce your fault. Does you reported problem only happen in the descent? What happens if you do not select Landing Lights? When you get the Access Violation error message please note and report the 2 addresses in text (the screenshots are difficult to read).

Share this post


Link to post
Share on other sites

Good afternoon,
as for the drivers of VRinsight Tack and Toggle I do not know, because when I opened the package I immediately connected the USB cable, and has installed itself;
I'll try to disconnect the two Opencockpit products when I'm downhill;
when I start a flight; start-ups, pushbacks, taxis, take-offs, climb cruise altitude, LINDA works well, while once the descent started almost in the approach phase when I'm at 10000 feet I turn on the VRinsight Tack and Toggle Landing lights switch and I notice that they do not work, and by checking any other LINDA command nothing works anymore, I do the landing, taxi to the gate and LINDA in addition to not giving more imput, it goes crashing;

I wanted to know, in the Joistick set-up, the VRinsight, and two products Opencockpit being written pad is right? do I have to set another name through the curtain?

I add all my commands on the simulator, they are disabled, because they are all configured via FSUIPC5.c123

 

you place enlarged screenshots I hope readable, one of the crashes when I'm in descent

 

39531667464_d2664d28c0_h.jpgScreenshot (147) by Alessandro Anile, su Flickr

I put the check mark on START GUI, when I start the LINDA simulator starts correctly, while when I close the simulator, LINDA does not close, I have to intervene manually, and crashes

 

25372755407_de30f11aed_h.jpgScreenshot (164) by Alessandro Anile, su Flickr

 

Share this post


Link to post
Share on other sites

Hi Alean

I has done a number of A320X test flights trying to reproduce your reported problem without success. I have flown the same profile you describe (take off/climb/descent/landing lights) and have experienced no issues. It is not the Landing Lights functions that are the problem. They work as per all other functions and would not result in the GUI crashing. Without being reproduce the crash I can offer no solution to you.

The Start with Sim checkbox will create (or remove) the following entry in FSUIPC5.ini:

[Programs]

RunIf1=CLOSE,C:\P3Dv4\modules\linda.exe

I have set and reset this a number of times and it is working for me. When P3D is closed, it can take up to 30secs for add-ons listed in the [Programs] block to shutdown correctly. This is a feature of FSUIPC5.

I can only suggest that you delete your LINDA.exe file and reinstall LINDA 3.0.5. All controls should be disabled in P3D (Options/Controls/Others). Only axes (aileron/elevator) and POV should be defined in FSUIPC and LINDA used for all buttons/switches.

Without more evidence and being able to reproduce it myself I can not solve your unique problem. Sorry.

 

PS. Make sure LINDA.exe is set to run as an administrator.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now