FSX-MS taxi2gate MUVR texture bleeding on arrival

[Alencp20 0]

Strange problem Im having with Taxi2Gate MUVR for fsx , if I start the the flight there every thing is alright all the textures loads ok, but if I fly there the texture at the begining of runway 06 start bleeding with the default textures.

 

I don't have any add on mesh, not orbx, just add-on airports,

I also check for duplicate afcads could not find any

I try contacting taxi2gate but those people don't respond back , they really have a bad customer service. I think is the worst of all the developers out there

[Jim Young 2,356]

There may not be many members who own T2G MUVR for FSX so you may have problems finding a solution here.  One possible solution might be to place the airport at the top of your scenery.cfg.  Another possible solution might be your scenery settings in the FSX.cfg.  For instance, I can make the land around an airport rise up or down based on the Texture Resolution setting.  The Mesh Complexity setting handles the height of the land around the airport.  You can try playing with those settings to see if they make a difference.  If you have any other airports in Cuba enabled from Taxi2Gate, try disabling all of them except MUVR.  Sometimes the elevation is affected by different airports.  You may have to place one of the airports above or below MUVR in your scenery.cfg. 

If you have no addon mesh, orbx vector data, or any other landclass scenery, then you might post your question in their forum - http://taxi2gate.org/?page_id=312&p=%3F

I did a Google search and did not see an issue related to your problem.

[Alencp20 0]

thanks jim for the response. To know for sure that this problem wasn't cause by any addon ,  I install fsx in another computer brand new and only MUVR and the problem still occurs , it is a taxi2gate problem I have tried contacting them but no luck on any response , they have a forum of their own I have tried posting my problem there with picture but some how my post don't get post. don't know what also  to do

 

thanks again for trying to help

[Alencp20 0]

any suggestions

[charliearon 3,024]

3 minutes ago, Alencp20 said:

any suggestions

I don't know very much about the Taxi2gate products.  Can you post one screenshot showing what you see?

[Alencp20 0]

where do I post the pic at

 

[charliearon 3,024]

48 minutes ago, Alencp20 said:

where do I post the pic at

 

Here  in your post.  See the paperclip in the lower left corner?  Take a pic, .JPEG is the best, make sure you can place it on your computer where you can find it.

 

[Alencp20 0]

I can't see the paper clip to attach the file

[charliearon 3,024]

25 minutes ago, Alencp20 said:

I can't see the paper clip to attach the file

OK, your only other option is to post your pic to an image hosting site and then use the insert other media tab to copy the URL into.

[Alencp20 0]

[charliearon 3,024]

Excellent pic showing what's going on.  You said if you start the flight at that airport, everything is OK, but flying into it causes what you show.  This is the only airport that does this?  Have you tried flying a 10 or 15 minute circuit taking off from that airport and landing there again?  I'm just trying to see if, maybe, your computer is becoming sluggish during a longer duration flight causing the textures not to form as fast as they should.

[Alencp20 0]

yes that its correct , every thing is all right if I start the flight there, during arrival from another sector this occur , if I start the flight there and and fly 10 to 25 circuit the airport upon landing every thing is normal

my computer is just fine I can maintain above 40 fps on any top add on airport , and I have a lot, but to be sure I install fsx in another computer and MUVR by it self to make sure and the problem still occur,

 

I can make multiple leg flight in one single flight , I'm  talking about maybe 5 to 6 airport without closing fsx and not OOM, example flytampa tampa to imaginesim Katl ( which is frame rate hog I can maintain above 40)to fsdreamteam KORD to flytampa Montreal and back , so performance wise is out of the question

Edited March 12, 2018 by Alencp20

[charliearon 3,024]

OK, sounds like everything on your end is good except for that airport.  I'm out of ideas, so your only option here is to wait and see if anyone else can give you any more info.  Your best bet is still with the Taxi2gate forum.

[Alencp20 0]

Thanks for trying to help , I least I learned how to post a picture on the forum