April 6, 20197 yr Hello, This is my first time posting on an AVSIM forum. When I finish landing in the PMDG 777 or 747, the brakes stay on. Even if I apply 100% N1, it reaches a maximum speed of 1 knot. When I try to set the parking brakes and release them, it doesn't work. I searched a lot on the internet, tried everything I could find, and nothing worked. When I tried to set the brake repeat slider in P3D to 50%, I still couldn't move. I do not have any of these problems in the 737NGX. Can anyone help me? Thanks in advance.
April 6, 20197 yr Hello, I wonder if you have burst all the tyres? It saeems to be very easy to do, all you need to do is use the brakes to slow down.🙂
April 7, 20197 yr Author http://tinyurl.com/y3ns9tps This is the brake setting I have in P3D. When I move the slider to 50%, I still have the same issue. I'm not experienced with PMDG aircraft, I'm still learning.
April 7, 20197 yr Author I landed with the brake slider at 50% on the 777, and everything was normal! Now I only need to try it with the 747.
April 7, 20197 yr That's what happens to me and I see those messages. Apparently it is my fault for not knowing how to slow the aircraft down and in the real world a gentle application of the brakes does not immediately set fire to the brakes and burst all the tyres. It might also be that using a simple joystick, the brakes are either full on or full off with no means to brake gently. Try a slow landing in an empty aircraft and use the reversers to slow down. You will use all of the runway but you should be able to taxi when the landing is over. Edited April 7, 20197 yr by Reader
April 7, 20197 yr Author 1 hour ago, Reader said: That's what happens to me and I see those messages. Apparently it is my fault for not knowing how to slow the aircraft down and in the real world a gentle application of the brakes does not immediately set fire to the brakes and burst all the tyres. It might also be that using a simple joystick, the brakes are either full on or full off with no means to brake gently. Try a slow landing in an empty aircraft and use the reversers to slow down. You will use all of the runway but you should be able to taxi when the landing is over. Thank you for your advice, but I also have this problem on autobrake. And when I do a rejected takeoff, I don't have this problem. Edited April 7, 20197 yr by klm729
April 7, 20197 yr I'm going to guess that this is being caused by landing severely overweight...in your screen shot with the tire press and temp warnings, you have over 355,000 lbs of fuel on the jet, which means you're significantly over the max landing weight even with no payload. Bob Scott | President and CEO, AVSIM Inc ATP Gulfstream II-III-IV-V Sys1 (MSFS20+24/XPlane12+11): AMD 9800X3D, water 2x240mm, MSI MPG X670E Carbon, 64GB GSkill 6000/30, nVidia RTX4090FE Alienware AW3821DW 38" 21:9 GSync, 2x4TB Crucial T705 PCIe5 + 2x2TB Samsung 990 SSD, EVGA 1000P2 PSU, 12.9" iPad Pro Thrustmaster TCA Boeing Yoke, TCA Airbus Sidestick, Twin TCA Airbus Throttle quads, PFC Cirrus Pedals, Coolermaster HAF932 case Sys2 (P3Dv5/v4): i9-13900KS, water 2x360mm, ASUS Z790 Hero, 32GB GSkill 7800MHz CAS36, ASUS RTX4090 Samsung 55" JS8500 4K TV@60Hz, 3x 2TB WD SN850X 1x 4TB Crucial P3 M.2 NVME SSD, EVGA 1600T2 PSU Fiber link to Yamaha RX-V467 Home Theater Receiver, Polk/Klipsch 6" bookshelf speakers, Polk 12" subwoofer, 12.9" iPad Pro PFC yoke/throttle quad/pedals with custom Hall sensor retrofit, Thermaltake View 71 case, Stream Deck XL button box Sys3 (DCS/P3Dv4/ATS/ETS): AMD 7800X3D, MSI MPG X870E Carbon, Noctua NH-D15S, 64GB GSkill 6000/30, EVGA RTX3090 Alienware AW3420DW 34" 21:9 GSync, Corsair HX1000i PSU, 4TB Crucial T705 PCIe5 + 2TB Samsung 970Evo Plus, TM TCA Officer Pack, Saitek combat pedals, TM Warthog, TM RS300 FF wheel/pedals, Coolermaster HAF XB case
Archived
This topic is now archived and is closed to further replies.