October 30, 20196 yr I have installed MCE following the valuable hints in this forum. The speech recognition is excellent. So far every command is understood, as I always can follow up in the top left corner of the main screen. Unfortunately my commands sometimes are not translated into action. And so I have to repeat some commands up to five times. What can I do to improve this situation? Arndt Laube Arndt Laube P3Dv4.5 and P3Dv5 Brunner CLS-E Yoke & Rudder, 2x Logitech Throttle, several GoFlight modules Intel i7 9700K, 16 GB RAM, Geforce 1080Ti, monitors 3840 x 2160 and 1360 x 768
October 30, 20196 yr Commercial Member 1 hour ago, Arndt777 said: I have installed MCE following the valuable hints in this forum. The speech recognition is excellent. So far every command is understood, as I always can follow up in the top left corner of the main screen. Unfortunately my commands sometimes are not translated into action. And so I have to repeat some commands up to five times. What can I do to improve this situation? Arndt Laube Not all complex aircraft are supported. Currently 43 of them are, including all the major ones like PMDG, 7737, 747, 777, FsLabs A320, Aerosoft Airbus, QW 787, 757, BAe146 etc... Which one are we talking about here? Which simulator, FSX, Prepar3D V4? Gerald R https://www.multicrewxp.com
October 30, 20196 yr Author My sim is Prepar3D v4. The airplanes are A2A Bonanza and Comanche. I have defined a few view commands with Voxkey, and I would like to control these views by voice. For example: view overhead panel, view radio panel, ... It works in 70 % of all cases, but then there are also cases, there I have to repeat and repeat ... Arndt Laube Arndt Laube P3Dv4.5 and P3Dv5 Brunner CLS-E Yoke & Rudder, 2x Logitech Throttle, several GoFlight modules Intel i7 9700K, 16 GB RAM, Geforce 1080Ti, monitors 3840 x 2160 and 1360 x 768
October 31, 20196 yr Author In the meantime I tested with several other aircraft, including PMDG 737 NGX. There is always the same problem. Arndt Laube P3Dv4.5 and P3Dv5 Brunner CLS-E Yoke & Rudder, 2x Logitech Throttle, several GoFlight modules Intel i7 9700K, 16 GB RAM, Geforce 1080Ti, monitors 3840 x 2160 and 1360 x 768
October 31, 20196 yr Commercial Member 21 hours ago, Arndt777 said: My sim is Prepar3D v4. The airplanes are A2A Bonanza and Comanche. I have defined a few view commands with Voxkey, and I would like to control these views by voice. For example: view overhead panel, view radio panel, ... It works in 70 % of all cases, but then there are also cases, there I have to repeat and repeat ... Arndt Laube Could you list the custom commands? Gerald R https://www.multicrewxp.com
October 31, 20196 yr Author Crtl + Shift + A Ctrl + Shift + B ........ Ctrl + Shift + P Arndt Laube Arndt Laube P3Dv4.5 and P3Dv5 Brunner CLS-E Yoke & Rudder, 2x Logitech Throttle, several GoFlight modules Intel i7 9700K, 16 GB RAM, Geforce 1080Ti, monitors 3840 x 2160 and 1360 x 768
October 31, 20196 yr Commercial Member 16 minutes ago, Arndt777 said: Crtl + Shift + A Ctrl + Shift + B ........ Ctrl + Shift + P Arndt Laube I meant the custom speech commands that trigger those key combinations, not the keys. I assume you added them to ""Prepar3D Demo.vkp" Voxkey profile Gerald R https://www.multicrewxp.com
November 1, 20196 yr Author The speech commands are: Pilot View, Left Panel, Right Panel, Overhead Panel, Radio Panel, Fuel Panel, Landing View, Top Down View, Rear View, View Left, View Right, Left Side View, Right Side View. I have created a special Voxkey profile. The different views have been created with ChasePlane. When I am using one of my GoFlight modules and press the keys, then there is always an immediately a reaction to all keys. If I am using MCE, then with approx. 30 % of the commands I have problems. Arndt Laube P3Dv4.5 and P3Dv5 Brunner CLS-E Yoke & Rudder, 2x Logitech Throttle, several GoFlight modules Intel i7 9700K, 16 GB RAM, Geforce 1080Ti, monitors 3840 x 2160 and 1360 x 768
November 1, 20196 yr Commercial Member 1 hour ago, Arndt777 said: The speech commands are: Pilot View, Left Panel, Right Panel, Overhead Panel, Radio Panel, Fuel Panel, Landing View, Top Down View, Rear View, View Left, View Right, Left Side View, Right Side View. I have created a special Voxkey profile. The different views have been created with ChasePlane. When I am using one of my GoFlight modules and press the keys, then there is always an immediately a reaction to all keys. If I am using MCE, then with approx. 30 % of the commands I have problems. Thanks. Since you created a separate Voxkey profile, you may want to delete "Prepar3D Demo.vkp". This will ensure MCE loads yours. Because there are built-in commands to control views, you need to disable these in <Sim> tab of the MCE user interface Gerald R https://www.multicrewxp.com
November 3, 20196 yr Author Thank you, Gerald! I did this, but there was no improvement. It seems that there is some problem in the communication between MCE and ChasePlane. But otherwise MCE is working great! Arndt Laube P3Dv4.5 and P3Dv5 Brunner CLS-E Yoke & Rudder, 2x Logitech Throttle, several GoFlight modules Intel i7 9700K, 16 GB RAM, Geforce 1080Ti, monitors 3840 x 2160 and 1360 x 768
November 3, 20196 yr Commercial Member 2 hours ago, Arndt777 said: Thank you, Gerald! I did this, but there was no improvement. It seems that there is some problem in the communication between MCE and ChasePlane. But otherwise MCE is working great! There is no need for communication with ChasePlane when it comes to this simple task. Voxkey will just send a key combination that is tied to your custom command, the same way you would press the key combo manually. It doesn't need to know anything about CP. Make sure no other add-ons are fighting for same hotkeys. Gerald R https://www.multicrewxp.com
Archived
This topic is now archived and is closed to further replies.