15 hours ago, HarryS said:

NOTE: Both switches one and four have aux position not just switch one.

Thanks for the detaile test.

Re-download patch and just rerplace "mce.exe" and "mciFly744.dll"

Should get most of them if not all sorted

On 2/1/2020 at 6:33 AM, FS++ said:

Re-download patch and just rerplace "mce.exe" and "mciFly744.dll"

Trim Air = All Good

Starting From OFF:
hydraulic demand one auto = Good
hydraulic demand two auto = Good
hydraulic demand three auto = Good
hydraulic demand four auto = Good

Then:
hydraulic demand one on = Good
hydraulic demand two on = Good
hydraulic demand three on = Good
hydraulic demand four on = Good

Then:
hydraulic demand one auto = Good
hydraulic demand two auto = No Action
hydraulic demand three auto = No Action
hydraulic demand four auto = Good

Then:
hydraulic demand one off = Good
hydraulic demand two off = No Action
hydraulic demand three off = No Action
hydraulic demand four off = Good

Then:
hydraulic demand one aux = Good
hydraulic demand four aux = Good

Then:
hydraulic demand one off = Good
hydraulic demand four off = Good

Starting From OFF:
all packs on = Good

Then:
all packs off = No Action

Starting From OFF:
pack one on = Good
pack two on = Good
pack three on = Good

Then:
pack one off = No Action
pack two off = No Action
pack three off = No Action

On 2/1/2020 at 10:48 PM, HarryS said:

Trim Air = All Good

Starting From OFF:
hydraulic demand one auto = Good
hydraulic demand two auto = Good
hydraulic demand three auto = Good
hydraulic demand four auto = Good

Then:
hydraulic demand one on = Good
hydraulic demand two on = Good
hydraulic demand three on = Good
hydraulic demand four on = Good

Then:
hydraulic demand one auto = Good
hydraulic demand two auto = No Action
hydraulic demand three auto = No Action
hydraulic demand four auto = Good

Then:
hydraulic demand one off = Good
hydraulic demand two off = No Action
hydraulic demand three off = No Action
hydraulic demand four off = Good

Then:
hydraulic demand one aux = Good
hydraulic demand four aux = Good

Then:
hydraulic demand one off = Good
hydraulic demand four off = Good

Starting From OFF:
all packs on = Good

Then:
all packs off = No Action

Starting From OFF:
pack one on = Good
pack two on = Good
pack three on = Good

Then:
pack one off = No Action
pack two off = No Action
pack three off = No Action

Patch revised. Just re-download and replace 2 files (mce.exe and mciFly744.dll)

2 hours ago, FS++ said:

Patch revised. Just re-download and replace 2 files (mce.exe and mciFly744.dll)

That's it fellas. All good

Similar problem with PMDG 748, see my recent posting here 

 

On 2/4/2020 at 11:10 AM, HarryS said:

That's it fellas. All good

Well, I spoke too soon.

asking for flaps 5 from 10 goes to 25, ask for 5 again goes to 30, ask for 5 again stays at 30, any command after that no action but FO says it's been done each time.

transponder TARA goes to "ALT RPTG OFF", ask again does nothing, then ask for standby goes to XPNDR, then ask for TARA goes back to "ALT RPTG OFF"

autobrake 1 goes to 1 and FO says "Autobrake Low" then autobrake 2 goes to 2 and FO says "autobrake medium", then autobrake 3 goes to 3 and FO says "autobrake high", then autobrake 4 goes to 4 and FO says "autobrake maximum", then autobrake maximum stays at 4, then off goes to off and rto goes to rto

 

47 minutes ago, HarryS said:

Well, I spoke too soon.

asking for flaps 5 from 10 goes to 25, ask for 5 again goes to 30, ask for 5 again stays at 30, any command after that no action but FO says it's been done each time.

transponder TARA goes to "ALT RPTG OFF", ask again does nothing, then ask for standby goes to XPNDR, then ask for TARA goes back to "ALT RPTG OFF"

autobrake 1 goes to 1 and FO says "Autobrake Low" then autobrake 2 goes to 2 and FO says "autobrake medium", then autobrake 3 goes to 3 and FO says "autobrake high", then autobrake 4 goes to 4 and FO says "autobrake maximum", then autobrake maximum stays at 4, then off goes to off and rto goes to rto

 

Please re-download and replace 4 files

mcpmd74V2.dll

mce.exe

2 files in <CandC> folder.

Thanks.

Suggest you start aircraft, wait until count down in green bar is at zero, then start MCE.

This guarantees aircraft has completely initialized and MCE can get data from it as expected. Applies to all supported PMDG aircraft.

 

2 hours ago, FS++ said:

Suggest you start aircraft, wait until count down in green bar is at zero, then start MCE.

This guarantees aircraft has completely initialized and MCE can get data from it as expected. Applies to all supported PMDG aircraft.

 

Always wait for initialization but will go through all the flows in order from cold & dark. Will let you know if I find any issues.

10 hours ago, HarryS said:

Always wait for initialization but will go through all the flows in order from cold & dark. Will let you know if I find any issues.

Maybe confused here as well as the thread refers to PMDG 748.

Replace both "mcpmd74V2.dll" and "mciFly744.dll" in <MCE dlls> folder.