August 25, 20205 yr Hi guys, This has been driving me crazy and I cannot seem to find an answer. Tried searching the forum... I would like to use a yoke for yoke controlled planes but use a stick for stick controlled planes (Cub, etc.). I can get a stick to use the ailerons and the yoke to use the elevator or vice a versa. but not both axis alone. Help! Thanks guys..
August 25, 20205 yr In the controller settings, select each controller in turn and manually assign the axis and buttons on each. Unless the sim does not have the ability to allow a single axis to be used simultaneously by two different controllers... GregH Intel Core i7 14700K / Palit RTX4070Ti Super OC / Corsair 32GB DDR5 6000 MHz / MSI Z790 M/board / Corsair NVMe 9500 read, 8500 write / Corsair PSU1200W / CH Products Yoke, Pedals & Quad; Airbus Side Stick, Airbus Quadrant / TrackIR, 32” 4K 144hz 1ms Monitor
August 25, 20205 yr Moderator You're ALMOST there. If you have the same axis on two controllers, they will interact and you will get strange results. Solution I used is to create a null profile for each controller. Then when you want to fly with the yoke, enable the yoke and enable the NULL version of the stick so it doesn't interfere and vice versa. I have a ch yoke, rudders , TQ and saitek X55 all connected so I just select the controllers I want to use and deselect (null profile) the others. HTH, Vic RIG#1 - I9 14900K MSI Pro z790 RTX 5070Ti 40" 4K Monitor 3840x2160
August 25, 20205 yr Author Hey Vic! Thank you! I think I can figure it out. Maybe? LoL. I appreciate that. I will let you know how I make out. CH flight sim yoke, CH pro pedals, Saitek throttle, Oddysey VR gear, Xplane 11, FS 2020 Deluxe
August 25, 20205 yr Moderator Not at my flight system but it is pretty simple - First, select each device and set it up the way you want giving it a profile name ( CH Yoke Full I use) Then select the first one say CH YOKE FULL - down below tyhere is a profile manager selection - select it - use the icons to DUPLICATE the current (CH YOKE FULL) Profile and give it a name (CH YOKE NULL) - remove all axis assignments - save it. Repeat for each device where there may be a conflict, then select the full yoke and null stick, or vice versa. If you want youi can set up different profiles for different aircraft the same way, just keep in mind that the same setting in different devices at the same time will cause problems. Have fun! 🙂 Vic RIG#1 - I9 14900K MSI Pro z790 RTX 5070Ti 40" 4K Monitor 3840x2160
August 25, 20205 yr 3 hours ago, vgbaron said: You're ALMOST there. If you have the same axis on two controllers, they will interact and you will get strange results. Solution I used is to create a null profile for each controller. Then when you want to fly with the yoke, enable the yoke and enable the NULL version of the stick so it doesn't interfere and vice versa. I have a ch yoke, rudders , TQ and saitek X55 all connected so I just select the controllers I want to use and deselect (null profile) the others. HTH, Vic this sir, hat off, i think this should go into the tips and tricks section..
August 25, 20205 yr Moderator 25 minutes ago, wim123 said: this sir, hat off, i think this should go into the tips and tricks section.. Done RIG#1 - I9 14900K MSI Pro z790 RTX 5070Ti 40" 4K Monitor 3840x2160
Archived
This topic is now archived and is closed to further replies.