September 22, 20205 yr Hey folks, I have the PMDG 737 NGXu installed on P3D v4.5 and there is a yellow message shown on PFD (INSTR Switch) see the snapshot. I looked up for it in all NGXu's manuals but not found. I was wondering, What does it indicate to? Is it a warning message? If yes, how to remove it? Do I have to solve it before the flight? Finally, I face a problem of engaging the CMD after take off, Do this (INSTR SWITCH) has any effect on CMD engagement? Thanks a lot in advance. Regards, Mazin Yousif
September 23, 20205 yr It means that both the captain's and FO's inertial reference sources are selected to the same side. Look at the IRS selector switch on the Navigation Panel (overhead)--should be in center (Normal) position. Bob Scott | President and CEO, AVSIM Inc ATP Gulfstream II-III-IV-V Sys1 (MSFS20+24/XPlane12+11): AMD 9800X3D, water 2x240mm, MSI MPG X670E Carbon, 64GB GSkill 6000/30, nVidia RTX4090FE Alienware AW3821DW 38" 21:9 GSync, 2x4TB Crucial T705 PCIe5 + 2x2TB Samsung 990 SSD, EVGA 1000P2 PSU, 12.9" iPad Pro Thrustmaster TCA Boeing Yoke, TCA Airbus Sidestick, Twin TCA Airbus Throttle quads, PFC Cirrus Pedals, Coolermaster HAF932 case Sys2 (P3Dv5/v4): i9-13900KS, water 2x360mm, ASUS Z790 Hero, 32GB GSkill 7800MHz CAS36, ASUS RTX4090 Samsung 55" JS8500 4K TV@60Hz, 3x 2TB WD SN850X 1x 4TB Crucial P3 M.2 NVME SSD, EVGA 1600T2 PSU Fiber link to Yamaha RX-V467 Home Theater Receiver, Polk/Klipsch 6" bookshelf speakers, Polk 12" subwoofer, 12.9" iPad Pro PFC yoke/throttle quad/pedals with custom Hall sensor retrofit, Thermaltake View 71 case, Stream Deck XL button box Sys3 (DCS/P3Dv4/ATS/ETS): AMD 7800X3D, MSI MPG X870E Carbon, Noctua NH-D15S, 64GB GSkill 6000/30, EVGA RTX3090 Alienware AW3420DW 34" 21:9 GSync, Corsair HX1000i PSU, 4TB Crucial T705 PCIe5 + 2TB Samsung 970Evo Plus, TM TCA Officer Pack, Saitek combat pedals, TM Warthog, TM RS300 FF wheel/pedals, Coolermaster HAF XB case
September 23, 20205 yr Author 6 hours ago, w6kd said: It means that both the captain's and FO's inertial reference sources are selected to the same side. Look at the IRS selector switch on the Navigation Panel (overhead)--should be in center (Normal) position. Thanks , but as I know there is no center position (Normal) please have a look at my setting right now: Is that what you meant? Regards, Mazin Yousif
September 23, 20205 yr also you havnt entered your v speeds in the fmc, too clear that message go to your overhead panel in the navigation switches just below the yaw damper switch make sure the irs switch is set to normal in the middle Edited September 23, 20205 yr by pete_auau I7-8700k,Corsair h1101 cooler ,Asus Strix Gaming Intel Z370 S11 motherboard, Corsair 32gb ramDD4,, gtx 1080ti Card, RM850 power supply Peter kelberg
September 23, 20205 yr Author 2 hours ago, pete_auau said: also you havnt entered your v speeds in the fmc, too clear that message go to your overhead panel in the navigation switches just below the yaw damper switch make sure the irs switch is set to normal in the middle Thanks, I have got it now and the aircrafts works just fine Regards, Mazin Yousif
Archived
This topic is now archived and is closed to further replies.