TiRex

Anton, yes I tried changing the tail number, but this did not solve the problem. I hat to load the MD-11 first and then the 737 NGX. Next time I'll try to load a different 737 model to see, if this also solves the problem. Loading a FSX standard aircraft does not help. Roland Koller

I think, this is the same problem, as I had with the M-Panel (see my post at http://forum.avsim.n...ost__p__2049703). The only solution I found so far was to map the controller key command to the 737 NGX key command with FSUIPC, even if the key commands are the same. This step was not necessary in all other aircrafts I have, including MD-11. Roland

Hi Dylan, when I have this issue, the VC also does not work. It just shows black screens as you can see in the screenshot from Rullstolen and I can do nothing. In FSX settings I have configured Virtual 3-D-Cockpit as the standard cockpit view. Roland Koller

Hi I found a bug in the key commands assignment. The key command for BARO STD does not toggel BARO STD. Instead it toggles BARO IN/HPA. In this example SHIFT+CTRL+1 and SHIFT+CTRL+2 both toggle BARO IN/HPA. Roland Koller

Now I have this issue again. Started FSX and loaded 737 NGX. No 20 sec initialization, just corrupted panels: 2D-Cockpit: Overhead: Radios: IRS: CDU: When closing FSX, FSX hangs and I must kill it via task manager. Restarting FSX does not resolve this. I have to load the PMDG MD-11 and then 737 NGX and all is fine again for the moment... Roland Koller

Hi Andy, thank you for your advice, but if I configure nothing in FSUIPC, the M-Panel does not work properly with the 737 NGX. I have to rotate the knob on the M-Panel several times to get the heading increased by 1. With the key assignment I described above, the M-Panel works, but I still have some troubles with fast rotating the M-Panel knob. I tried the VRinsight Mod, but for this I have to install and run the Virtual Serial Ports Emulator (VSPE), which unfortunately is not free for 64bit environments. Without VSPE I cannot use the buttons + switches tab in FSUIPC. But with VSPE the assignments in the buttons + switches tab work much better then the key presses assignments, because also the M-Panel fast rotation codes are recognized by FSUIPC. So I'm not sure now, what I shall use. I think, I will test both variants for a while to see, which one works better Anyway thank you very much for the VRInsight Mod hint, I never heard about this before. Roland

Ok, I found the solution: I have to provide the keycode and the ctrl-code in the parameter field as mentioned in the FSUIPC users guide. For the ctl+T I have to enter "84+10" in the parameter field. You can find the keycodes in the FSUIPC advanced users guide. Roland

Hi Chris, how did you accomplish this? I assigned e.g. LCONTROL+t in the M-Panel Key Mapper for Heading Decrease and assigned CTRL+T for Heading Selector Dec in the NGX FMC. But this does not work. Then I tried the following assignment in FSUIPC, but this does not work either: Tried also "Heading Bug Dec" in "Control sent when keys pressed", but this didn't change anything. Can you please tell me how you did the assignment e.g for the heading knob? TIA! Roland

Hi, I also have this problem sometimes, especially after a CTD. Then when I restart FSX and load the 737 NGX all 2D panels are corrupted (no knobs, no switches). CDU just diplays a corrupted image. In the VC I only see black screens. I tried uninstalling 737, deleting all remaining PMDG 737 folders and .DLLs, reinstalled the 737 but this did not solve the problem. After some attemps I found out, that all works fine again, if I load the PMDG MD-11 prior to the 737 NGX. Roland Koller

Same issue in Austria