Sunil

thanks mate Sunil

How can i improve taxi lights in the night . i can barely see the runway marking in the night in some airports Sunil

Thanks PRO930 for your advice Sunil To: Pcubine Sir The 10 h is with Ground Preparation

Dear Sir , Thanks, I run a AUSU SABERTOOTH Z77 Gaming Mother Board i7-2600k @ 3.40hZ 32 GB Memory. Windows 7 with 64 Bit operating System Display NVIDIA GTX 570 and NVIDIA GTX 660 both Each 4 GB Memory 10 numbers wide SAMSUNG monitors Add-ons: PMDG 737 NGX SP1 with all Service updates Zaitek Pro Flight Yoke System Zaitek Rudder Pedals Zaitek Radio Panel Aiviassoft EFB Around 30 Aerosoft Pay wear Airports FSUIPC 4.486 FS Co Pilot & FS inn Active Sky 2012 PROATC-X FS flight Keeper Rex Latitude It happens in any flight long or short. After changing the RW I tried what you suggest it all works fine, moment I change the RW to a another one and only landing this take place I am planning to do that going for a PMDG support Ticket. Sunil

i have got all the latest version installed, i do not use any other aircraft's only pmdg 737ngx

Dear Sir, I have come across a problem in my FMC I hope someone can help me to solve this problem. I have been using PMDG 737NGX for last few years and flown more than 400 flight in my FSX. During this period I have experience FSX crashing around 20 times. I used to analyze what is happening, every time this happens when I try to land just 3 or 4 ml to the landing point, the computer gets freezes and after few second the FSX crashes and a message appears “FATAL PROBLEM SHUTTING DOWN”. During this period I checked what I have done this to take place, very time I I have to change the landing RW for the second time I have experience this. When I do the trip again without changing the RW, it works beautifully. The last time this happened yesterday when I try to land EDDF (When there is no ATC I used PROATC” and the assigned RW was 25R Before Descending, but around FL100 the PROATC changed to 25L by that time I have programmed the FMC and re did the Programming. And the problem took place. I re did this Trip LSGG to EDDF again this time I did not Change the RW but for the First time I programmed the RW 25L and it worked. Can the Support team or A veteran can help me to solve this, after flying a 10H flight when this happened you can understand the Frustration. Sunil Alles

Thank You For the advice it was side by side

Hi Can someone help me to correct this problem? My Lower DU is blank I tried so many ways to get it going no success Sunil

Dear All I amusing Matrox TripleHead 2 Go monitors for my 2d cockpit and 4th monitor for my Gauges. is there any way that i can save these setting for loading again without rearranging all over Thanks Sunil

James Ok Thanks will try Active Sky 2012 also nothing like trying as i have both i will be in a better possition to comment Thanks sunil

Thanks for all the comments i ttok the advuce of james and went for rex 2012 i will try and comment once a agin thnks fro your time it is a great community

Hi Can someone help me! I have been using 737NGX for last 6months, For example OMDB on landing I set the pressure to QNH 0998 as per the Vrtoute date But when I check with PFD/ and information Via Fsinn the pressure show as QNH1013 When try to land after pressure selector B some time the landing is hard or above the RWY How to set this correctly Thanks Sunil

How to download HF4

Dear Sir,i have tried several time to run 737NGX with FS co pilot (Fs Inn) and every time after the climbing to @FL180 and above it gradually stop climbing and the outbound Du start going up and down between 0-400 and CDU legs page fl level all so start flickering to dots..... ad fl24000 and to top of the climb indicates around 650Nm. CDU gives the message “Buffet Alert” What is it? The Speed start dropping to almost 200@ FL240 why is this???When i fly without Co pilot (Fs inn) it’s perfect, and tried with Squake Box no problem.I do fly PMDG 747 with Fs Inn no problem. i have done almost 500h with 747i am using FSXFs Inn is very good please help me with this problum

Dear Sir,i have already purchased the 747 and MD 11 products in my computer, Now i have purchased the NG737 and i wish to know the following :1. Doi have to remove the other product before i install the NG7372. Or can i install without removing the 747 and MD11?ThanksSunil AllesEmail me