This is a known problem. The issue is my gauge is peeking at the pixels just to its upper left to gauge shading brightness, and in this case some bright overhead pixels are in the way.A workaround is to move the overhead up a bit to completely uncover the VSI (or down to completely cover it). Sorry, but I cannot come up with a better solution. This automatic shading was a major hassle, but also I think a significant victory given that I didn't want to modify the main panel bitmap or its lit version inside one of the PIC gauges.About the landing view panel, I don't have anything to do with that. I'm surprised a VSI would even be visible in a visual landing view. Sorry, but I can only do so much.Lee Hetherington (KBED)http://vatsim.pilotmedia.fi/statusindicato...tor=OD1&a=a.jpg

well, what shall I say: just installed it, made 2 flight and it works GREAT! thanx for this wonderful addon!CheersPhilCome to DAD!http://www.dangerous-airports.com/images/dad_logo.jpgAMD XP 2700+, 512 MB, ASUS A7N8X, GF4 440, 17" TFT

Tjena MatsNice to see a fellow Stockholm guy on the forum..Well....it was trivial,basic and wery obvious and once again I've been too eager to read the manual correctly (-: -- feel soooo stupid.Thanks MatsFredrik(StenSture d.y. ;) )

Hello There, TCAS gague on My 767 failed with red letters "TCAS FAILED"Best Regards.

install FSUIPC at least version 2.83, so rather a newer version.Cheers

Clearly I should have made the message "READ THE DIRECTIONS" instead.Lee Hetherington (KBED)http://vatsim.pilotmedia.fi/statusindicato...tor=OD1&a=a.jpg

I know this is in the wrong forum. . . but, BAH! Mind explaining to me the needed equipment to make the DF734 tcas work?You can do it via private message if you wish, dont want to pollute this great forum with a guppy question.

Hello there, All directions followed, all manuals read, all additional software reqired installed, yet, "TCAS FAILED" is there.Best Regards.

Great work Lee, it's very sleek looking and has very fluid animation. :-D

Sorry for the quip there. What version of FSUIPC? Bring up the FSUIPC options page to see. What is the TCAS range set to in FSUIPC (on the technical page)?Lee Hetherington (KBED)http://vatsim.pilotmedia.fi/statusindicato...tor=OD1&a=a.jpg

It should work with FSUIPC and AIBridge. You might have to turn it on though. I can't remember if there is a hidden click spot mid left side of the EHSI, or perhaps it is a setting on the transponder. It definitely works with AIBridge.Lee Hetherington (KBED)http://vatsim.pilotmedia.fi/statusindicato...tor=OD1&a=a.jpg

Hello, reinstalled FSUIPC version 2.97 from one hardrive to the right hardrive on my system's FS 2002, modules folder, "TCAS FAILED" is not displayed anymore. Best Regards,

Hello, reinstalled FSUIPC version 2.97 from one hardrive to the right hardrive on my system's FS 2002, modules folder, "TCAS FAILED" is not displayed anymore. Best Regards,

Richard is comming out with a newer verison of FSUIPC that will make it work right, till then use one that is OLDER than 2.97 i.e. 2.95 Best Wishes,Randy J. [email protected]" A little learning is a dangerous thing"AMD XP 2100 |MUNCHKIN 512 DDR RAM |ECS[/b ] K7S5A MB |[b]GF3 64 MEG |WIN XP PRO |MITSUBISHI DIAMOND PLUS 91 19"

2.972 will work fine for AI traffic. AIBridge traffic will blink.Lee Hetherington (KBED)http://vatsim.pilotmedia.fi/statusindicato...tor=OD1&a=a.jpg