Using both rxp GNS's?

[Barnstormer16 1]

I had both installed in the P46T in the old computer but when I try in the new Jetline the 530 installs but the 430 has no screen on the pop up and the one in the VC panel says it won't work. The 430 is working fine in other Carenado aircraft. This is the only one I've ever had both in, and it's not a big deal to me, but strange never the less.

[Bert Pieke 7,585]

This is what the panel.cfg should look like:

 

//--------------------------------------------------------

[Vcockpit02]

Background_color=0,0,0

size_mm=1024,1024

visible=0

pixel_size=1024,1024

texture=$Panel_2

 

gauge00=WX_Gauge_3D_P46T!WXGauge, 9,9,492,309

//gauge01=GPS_530_3D_P46T!gps_500, 7,337,493,358

gauge02=Radio_P46T!RadioAdf, 524,670,496,100

//gauge03=GPS_430_3D_P46T!GNS430_nc2, 517,259,497,258

........etc

 

//--------------------------------------------------------

[Vcockpit04]

Background_color=0,0,0

size_mm=1024,1024

visible=0

pixel_size=1024,1024

texture=$Panel_4

 

gauge00=rxpGNS!GNS530, 12,337,493,358

gauge01=rxpGNS!GNS430, 515,260,497,258

 

Send me a PM if you cannot make it work!

[Barnstormer16 1]

Okay, I failed to say in the body of my question that it's the RXP 530 & 430 I've installed via the installer that came with the P46T. The RXP GNS530 works, the 430 does not. Maybe I need to mess around with Vcockpit02 a bit. On mine the units not in use are listed as shown below with a ; after the = mark instead of // before the gauge...:

 

 

[Vcockpit02]

Background_color=0,0,0

size_mm=1024,1024

visible=0

pixel_size=1024,1024

texture=$Panel_2

 

gauge00=rxpWX500!RDR, 9,9,492,309

gauge01=;GPS_530_3D_P46T!gps_500, 7,337,493,358

gauge02=Radio_P46T!RadioAdf, 524,670,496,100

gauge03=;GPS_430_3D_P46T!GNS430_nc2, 517,259,497,258

gauge04=DIGTTRANS_P46T!transponder, 516,529,501,126

gauge05=Radio_P46T!RadioTrans, 520,126,496,112

gauge06=Radio_P46T!RadioAudio, 520,8,498,98

gauge07=GAUGEP46T!Gauge_Anum_R, 381,786,635,229

gauge08=GAUGEP46T!Gauge_Engine_Trend, 14,711,299,298

[sheepfu 3]

With mine, I used the Carenado installer to give me the right locations for the RXP's but I used the RXP installer to give me the correct RXP.cfg file. the RXP.cfg is what runs the RXP's in the sim. to the best of my knowledge, the Carenado software does not write to this file.

[Bert Pieke 7,585]

What RXP.cfg file are you referring to?

 

Is it the rxpgns.ini file?

[sheepfu 3]

Yeah, I was at the office and couldn't remember exatly what it was called.

[Bert Pieke 7,585]

Was just informed that this problem was fixed with a new install of the GNS units, which is

a reminder that if you switch to a new computer, you cannot simply copy over these gauges,

but you you have to re-download/re-install them.

[AMR089 0]

Hello Guys ! Hello Mr.

Bert Pieke
AS i told you in the other forum about the issue i had faced . i installed P46T Malibu and then i installed The XP integration inside the Malibu folder CAR_XP after i installed the reality xp gns530/430 then when i chose the aircraft at my FSX it crashed immediately also i fixed the panel.cfg as mentioned in ur previous comments  , i do the same with A36 and still the same problem . any solution plzzz .but if i don't install the xp integration from the aircraft install folder and just set the RXP config for the aircraft i get a view cockpit(only 2D view but when pop up the gns530 the default one in 3d cockpit view still the same ) like in pictures below thank you in advance waiting for ur response   

[AMR089 0]

well i don't know why i can not upload pictures here but if you want i can send it via e-mail ( please leave for me ur email )......thanks 

[Bert Pieke 7,585]

Sent you a PM.