Jump to content

vancouver scenery library order


fluffyflops

Recommended Posts

Hello.

 

I have reinstalled fax from scratch last week and have a coast line issue around cyvr. There is land instead of water.

 

I've checked the usual culprits of terrain.cfg and the Vancouver+ v3 entries and the ultimate Terrain entries in the terrain.cfg. they are fine.

 

I managed to get the issue down to a conflict of scenery as listed below.  I'm quite sure it's a scenery library order issue, and a conflict with orbs pnw and ultimate Terrain.

 

Can some advise the order the scenery entries need to be (higher / lower) and which ultimate Terrain scenery entry needs to be unchecked to try and eliminate the issue.

 

1.fsdreamteam cyvr

2.fsaddon Vancouver + v3

3.Ultimate terrain USA

4.Ultimate terrain Canada

5.Ultimate terrain europe

6.orbx pnw

7.orbx nrm

8.orbx global

 

Thanks a million in advanced

 

 

 
 
 
 
14ppkc-6.png
  913456
Link to comment
Share on other sites

Here is my Scenery.cfg attached below.  You would most likely want to start at entry #129 and working down from there.  Remember that the last entry in the .cfg will show as the first scenery area in the FSX Scenery window.  I might have a few products that you may not have but the proper ordering is provided.  Also, with Orbx products be sure to install the latest library objects after updating any of their products, it must be done last.

 

Good luck!

 

 

Scenery.txt

\Robert Hamlich/

 

Link to comment
Share on other sites

Just took some time to look at FSX Settings-Scenery Library.

 

From the top down I have the following:

 

FSDreamTeam Vancouver

Orbx FTX NRM

Orbx FTX PNW

Orbx Open LC (Global)

UT Europe

UT Canada

UT USA

 

Your Vancouver+ should be sandwiched between FSDT Vancouver and Orbx FTX NRM.  You could try disabling the sceneries 1 by 1 in FSX Settings-Scenery Library to troubleshoot.  If all else fails have a look at the Vancouver+ website or manual, you should find what you are looking for there.

\Robert Hamlich/

 

Link to comment
Share on other sites

You don't say?  I have been wanting to get up to Whistler to ski for years, been there a few times during the summer but haven't been brave enough to face the slopes.  I hope you have a great time.

 

You probably already know about the FSX Scenery Config Editor to make moving of your sceneries easier, just in case you do not here is a link:

 

http://sourceforge.net/projects/fs-sceditor/files/latest/download

 

You can raise or lower scenery priorities much simpler (and safe) using the "List" tab.  And the beauty of this editor is that it automatically checks for scenery errors.  Be sure to make a backup of your main scenery.cfg before you make any changes.  FSX has 3 Scenery.cfg's, the main one is located in C:\ProgramData\Microsoft\FSX

 

All the best,

 

Robert

\Robert Hamlich/

 

Link to comment
Share on other sites

Hi Robert,,,

 

yup my brother kives in coquitlam so I go over quite a bit...

 

so i solved the problem, took me 8 hourts to work it out but ive sussed it,,,so it was 2 areas actually that where the problem causing land instead of water, having either scenery areas on causes the issue they are 

 

1,FTX_NA_PNW06_cvx

2.UT_exclusions for default scenery.

 

cheers 

 
 
 
 
14ppkc-6.png
  913456
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
×
×
  • Create New...