Hi there please i used to have normal fps around 30-40 in the sky  but when i install this effect 777 immersion this effect really makes worst straight drop to 5-10 fps even on high altitude, could you please suggest what is the issue ? .. 

 

 

 

i would say its either the program itself is causing low FPS(which is common) or your computer cant handle it.

• Processor
  i7-4930k

• Processor Cores
  6

Processor Speed

3.4GHz Not OC

RAM

12GB

Video Board Manufacturer

EVGA

Video Board Model

GeForce GTX 970

Video Memory

4095MB

Mother Board

ASUSTEK  SABERBOOTH X79 

Monitor

Asus 27" PB287Q 3840 X 2160

Operating System

Windows 8.1 64bit

Yoke

Saitek Cessna Pro Flight Yoke

Rudder Pedals

Saitek Pro Pedals

Other

Saitek Throttle Quadrant - Saitek Radio Panel - Saitek Pro Flight Switch - Saitek Cessna trim wheel

 

 

Is this Spec not enough,  i mean at first when  pre flight its ok the fps is ok when the flight is in mid air on cruise the  contrails wing condensation really makes worst when i switch camera and even on cockpit the performance is very bad... if you have save issue please let me know. 

 

Best Regards

those specs are totally fine. i would say its the program its self. whats your frames locked to (try unlimited)

Frame is lock to unlimited

and its still laggy 

Yes, but when I uninstall or untick all immersion effect it's back to normal. Have u encountered this issue if u have installed and checked.

well since youve said that when you unticked the immersion it goes back to normal then its obviously the immersion program. Message or contact the creators about it and ask if they can release an update to fix dropping FPS

https://drive.google.com/file/d/0B4oITglwM_yjQXBIbU9ZLUZ3RGc/view?usp=sharing

 

Hello,

 

I have same problem with 777 Immersion, and I found out that my contrails is different from the official video or other flyer(something like engine spray come out from T7 wing)

it cause huge impact on my FPS..

 

When I uninstall 777 immersion, it return to normal.

 

Can anyone help me to solve the problem?

 

Currently setting:

Steve DX10 Fixer

SweetFX

Active Sky Next

REX 4 Texture Direct 

 

PC Spec

4790K 4.4GHz 

780Ti 3GB

12GB Ram

FSX installed in Samsung 840Pro SSD

Is the FPS-impact only noticeable when an effect runs or about the whole flight ?

 

Actually i have a FPS-drop when the spray-effect runs on takeoff.

All others are running fine.

Is the FPS-impact only noticeable when an effect runs or about the whole flight ?

 

Actually i have a FPS-drop when the spray-effect runs on takeoff.

All others are running fine.

when maintain FL300 or above, the effect come out and have FPS impact. Drop to FPS 20-23(Spot view), normally should have 30-40FPS

 

Wing condensation during takeoff not affect the FPS a lot for me.

You use the NVidia Inspector ?

If yes, what is your Antialiasing-Setting ?

Months ago I had 8xSQ and it caused a big FPS-hit when was above dense clouds from 30 to 5 FPS.

Now i´m on 8xS and it runs well.

 

Wing condensation should also not affect the FPS.

I meant the spray behind the plane if you give full thrust on takeoff.

Hi Guys, 

 

The solution for the following FPS Hit is due to Antialiasing Setting, If you use DX10  please make sure its on 4X Antialiasing not more than that, which works perfect well

 

 

Best Regards

I also found out that, Active Sky Next will make this wind spray effect above FL300(or cruise), if I not using ASN, the contrail will become normal as the official video and no FPS impact for me.

 

Is that any conflict between ASN & 777 immersion? Or something wrong in my ASN setting? 

Is there any way to improve fps under DX10?

Usually I have 30 fps with DX9 inflight and Immersion effects, but now with DX10 with contrails und wing condensation frames drop to 15-18.

Same with spray effects during takeoff and landing.

 

I don't want to lower antialiasing due to the effects, because all the rest is looking awful in that case.