I'm wanting to combine MCE and RC4 for my PMDG because i'm soon getting the 737 pedestal from FDS and i'll be handling all comms. So is anyone using these together and is it easy enough to get it going?

I could never get it to work consistently although others seem to have it working fine.

I use VAC  http://www.dwvac.com/

I also could never remember all of the MCE verbal commands and find it much easier to remember my own commands that I have used in VAC.

After creating a profile for RC it works flawlessly, the recognition is very good.

There is also "It's your Plane" from where I borrowed the command syntax to build my VAC profile.

http://www.itsyourplane.com/startup.asp?p=/html/home.asp

 

Here are the RC commands and keypresses if you choose to go with VAC and create a profile, you can add your own multiple phrases for each RC command in VAC,you are not limited to just one for each action. use these as a starter and add your own as you build up a profile..

List of Radar Contact 4 Voice Commands

Emits Keys CTRL+SHIFT+0
Select zero
Main menu

Emits Keys CTRL+SHIFT+1
Select one
Acknowledge and contact
Affirm
Clearance delivery, ready to copy
Choose landing mode
Contact approach
Contact clearance delivery
Contact control
Contact delivery
Contact departure
Contact (the) destination tower
Contact ground
Contact next control
Contact tower
Delivery ready to copy
Direct to waypoint
Next control
Monitor tower
Ready for departure
Request taxi
Request vectored approach
Tune to the tower

Emits Keys CTRL+SHIFT+2
Select two
Abort take off
Declare rejected takeoff
Declare aborted takeoff
Flight critique
Get ATIS
Get local ATIS information
Get weather briefing
Going missed
Missed approach
Reject take off
Request departure runway
Request push and start
Request runway
Request runway for departure
Request to leave frequency for weather
Request visual approach
Request weather

Emits Keys CTRL+SHIFT+3
Select three
Contact ground for clearance
End radar contact
Get clearance
Ground ready to copy
Notam on course
Request P D descent
Request return to airport

Emits Keys CTRL+SHIFT+4
Select four
Clearance by F F S
Declare emergency
Request higher
Request I A P approach
Wind check

Emits Keys CTRL+SHIFT+5
Select five
Clearance en route
Clearance in air
Contact ground for push and start
Field in sight
Request landing runway
Request lower
Request runway for landing

Emits Keys CTRL+SHIFT+6
Select six
Unable to comply

Emits Keys CTRL+SHIFT+7
Select seven
Acknowledge
Acknowledge hand off
Acknowledge I F R clearance
Cleared for take off
Cleared to land
Cleared to {WAYPOINT} as filed
Copy {FLIGHTNUMBER}   (e.g. "Copy 1123")
Copy {AIRLINEATC} {FLIGHTNUMBER}   (e.g. "Copy Speedbird 1123")
Expect vectors runway {RUNWAY}
Line up and wait
Position and hold
Read back clearance
Ready to copy
Taxi into position and hold
Taxi to the ramp
Taxi to and hold short of
Traffic in sight

NOTE: To get {AIRLINEATC} and {FLIGHTNUMBER} ask, "What is our callsign?"

NOTE: The {AIRLINEATC} and {FLIGHTNUMBER} information is derived from the simulator's aircraft data... NOT from Radar Contact.   In Project Magenta installations, the information is pulled from the External Cockpit panel settings.

Emits Keys CTRL+SHIFT+8
Select eight
Previous menu

Emits Keys CTRL+SHIFT+9
Select nine
Select niner
Next menu

Emits CTRL+SHIFT+O
Over to next controller

Emits CTRL+SHIFT+P
Display flight plan

Emits CTRL+SHIFT+R
Please repeat instruction
Repeat instruction
Repeat last instruction

Emits CTRL+SHIFT+;
Save radar contact

Emits CTRL+SHIFT+L
Set nav frequencies

Emits CTRL+SHIFT+K
Hand back communications
Take over communications

Emits CTRL+SHIFT+M
Hand back plane
Take over plane

Thanks alot i'll try VAC out tonight. Is it pretty straight forward to setup etc?

Yes it is easy, Push to talk was probably the hardes part but I have a button on my yolk assigned to a keypress in Fsuipc (insert key) and have the following options setup in VAC.

 

Ok thanks alot i'll get to it tonight