Jump to content
Sign in to follow this  
hermannk1

JS4100 FMS setup

Recommended Posts

I recently dusted off my PMDG JS4100 and started flying her again.  Must say, a very nice aircraft.

One problem though:  I programmed the FMS as per the Tutorial, pressed LNAV and FULL MAP and set off into the skies.  The MAP showing my programmed route.  I connected AP, then VS and FL armed.  Nice going so far. When clicking on NAV it shows CAP and then...start to turn in a completely different direction from my Waypoints.  There is no way I can get it to follow the waypoints in the map.  Except by HDG.  But that is not supposed to work like that.  Any suggestions?

Share this post


Link to post

May be I'm wrong but if I remember, you must enter direct to your first waypoint...

Regards,


Richard Portier

MAXIMUS VI FORMULA|Intel® Core i7-4770K Oc@4.50GHz x8|NVIDIA GeForce GTX 1080ti|M16GB DDR3|Windows10 Pro 64|P3Dv5|AFS2|TrackIr5|Saitek ProFlight Yoke + Quadrant + Rudder Pedal|Thrustmaster Warthog A10|

Share this post


Link to post
14 hours ago, DrumsArt said:

May be I'm wrong but if I remember, you must enter direct to your first waypoint...

Regards,

I did enter the Direct To waypoint and still it follows completely the wrong route.

Share this post


Link to post

I always press LNAV twice to make sure it really is in LNAV mode. IIRC a single press of V/L or LNAV just "previews" it temporarily on the ND without actually changing the nav source for the AP.


ckyliu, proud supporter of ViaIntercity.com. i5 12400F, 32GB, GTX980, more in "About me" on my profile. 

support1.jpg

Share this post


Link to post
16 hours ago, DrumsArt said:

May be I'm wrong but if I remember, you must enter direct to your first waypoint...

Regards,

I get the idea that using the Garmin GTN 650 may have something to do with it.  When actually activating the GTN 650 during the flight and entering the same flightplan, the aircraft follows the GTN 650 rather than the JS4100's own FMS.  When the GTN 650 is not used at all, the problem remains with the JS4100 FMS not following the flightplan.  I've got the idea that even though the GTN 650 is in the background and not even activated, the JS4100 FMS is influenced by that.

Share this post


Link to post

I disabled the F1 GTN 650 in the J411 panel.cfg completely.  Tried the flight again and the FMS took to the flight plan with no problem!  Seems as if the GTN 650 interferes with the FMS even though it is not switched on. 

Share this post


Link to post
15 hours ago, Ecosse_821 said:

Does the JS4100 come with the GTN 650?  

No.  The GTN 650 is a F1 add-on Garmin.  Very nice.  A2A's aircraft make special use of it.

 

Share this post


Link to post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  
  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
×
×
  • Create New...