Hi there,

 

I have hard time to learn how to use FS2Crew for 747 but in some step he didn't do what i need. For example, Starting engines

flaps done for 10 or 20, flaps up after takeoff, APU off and .....

I am using VOICE but I gave up with it

any help? Please!

I am using P3D v4

Reminder

In 10.000 feet

i need hem to turn off wing light not logo light. Please!

Thank you for your help!

 

Mansour

Hi Mansour,

Please run the voice training again and be sure to follow the tutorial.

Make sure the expected phrase is displayed in the green bar.

 

The logo lights go off at 10,000, and they are turned on at 10,000 feet in the descent if it's dark.

Wing lights are used to spot ice on the wings.  You'd turn them on / off as required.

Is it better to use FS2Crew on the headset? My microphone is always hearing the readbacks from the FO (like "Speed checked, Flaps 20") and is then making Flaps 10 because he thought this was a new order.

Would be good to know what the best solution is.

Regards,
Timm Rehberg

22 minutes ago, xTiMm_ said:

Is it better to use FS2Crew on the headset? My microphone is always hearing the readbacks from the FO (like "Speed checked, Flaps 20") and is then making Flaps 10 because he thought this was a new order.

Would be good to know what the best solution is.

Regards,
Timm Rehberg

 

I suspect most people use headsets.  A generic USB one is best.

However, my advice would be to:

1. Keep the mic further away from your speakers.

2. Reduce the sensitivity of your mic.

Cheers,

Thanks a lot! Will try to change my mic settings.
Because I don´t want my FO to set Flaps 20 on approach, ask for Flaps 30 while he is returning the Flaps to 10 :D

Dear byork

IN 777 everything is good but the logo light

in 747 no not like that. Why? because audio is is rebating it many time like " welcome massage and ... etc 

i did like the tutoring manual and it is not respond for engines and flaps too

Please! try to fix it ASAP

Also i don't need him to tern off the logo light.

 

Mansour

in few minute i did a flight from OEAB -> OERK I follow up the manual as you told me but engines and flaps not working with FO

NON - AUTO START (ENGINES MUST BE STARTED INDIVIDUALLY)

o START ENGINE 4

o START ENGINE 3

o START ENGINE 2

o START ENGINE 1

 

12 hours ago, mansour said:

in few minute i did a flight from OEAB -> OERK I follow up the manual as you told me but engines and flaps not working with FO

NON - AUTO START (ENGINES MUST BE STARTED INDIVIDUALLY)

o START ENGINE 4

o START ENGINE 3

o START ENGINE 2

o START ENGINE 1

 

 

Hi Mansour,

You need to be more specific pls.

If it's in the manual, and you see the phrase in the "Green Bar", it should work.

 

On 11/19/2017 at 7:42 AM, byork said:

 

Hi Mansour,

You need to be more specific pls.

If it's in the manual, and you see the phrase in the "Green Bar", it should work.

 

 

Dear byork

I start fs2crew from "Before Start Checklist" menu when I came to "Engine Start" menu it desn't work also flaps.

you have to check it. Please!

 

the FO con"t use the PMDG buttons because he can't Pressurize the Hydraulics and APU and Air Packs also flaps and lights and landing gear too.

That what is happen with me. He is not doing any thin with me.

Any help to fix it? Please!

Make sure you have the latest version of P3D installed (assuming you're using P3D).

If the FO can't press any buttons in the 747, it's because you don't have the latest version of P3D installed.

 

Yes, it is v4 but i don't want to upgrade until i see the good and the pad thing with v4.1

so if not that mean it will not work with me at all?

5 hours ago, mansour said:

Yes, it is v4 but i don't want to upgrade until i see the good and the pad thing with v4.1

so if not that mean it will not work with me at all?

 

From the FAQs:

 

Question:  I have P3D V4, and the FO is not moving any of the switches or pressing buttons.

Answer:  

You need to have the latest P3D V4 version.

To know what version of P3D V4 you have, right click on the Prepar3D.exe located in your main P3D folder.

Look at the "details" section / tab.

Look at the "file version".

You need to have 4.0.28.21686 or later installed.

More info here:

https://www.prepar3d.com/forum/viewtopic.php?f=6305&t=125533