Prepar3d version 4.5 CTD after linking UTL

[Gary1124 181]

I am putting together a Prepar3d Version 4.5 build and I just linked UTL 2 to P3D 4.5. Now after about 20 minutes of operation it CTDs. It is standard UTL 2 for FSX/P3D. Not the beta for version 5. Just got a forced Win 10 update to. Here is what I'm working with.

Ryzen 5 3600. 32 GB DDR4 3000

Radeon RX 580 8 Gig

Asus B450 motherboard 

240 gig SSD C

2 TB SSD D

P3d v4.5 on D

Addons

UT NA

ORBX Base

ORBX NA LC

ORBX Buildings

ORBX Airports Global Free.

Ultimate Traffic Live 2

FSRealWX trial (Active Sky P3D next Payday)

A2A V35 Bonanza (only aircraft addon so far)

Anyone have experienced this trouble and ideas? Thanks

 

[Bob Scott 7,715]

What's in the event viewer?

Has it done this more than once?

[Gary1124 181]

Yes, it has. Twice. First time before takeoff. 

How do I view event viewer? New to sim from FSX-SE.

Thanks

[Bob Scott 7,715]

2 hours ago, Gary1124 said:

How do I view event viewer? New to sim from FSX-SE.

See page 8 of the AVSIM CTD Guide, link located at right margin of home page.

[Gary1124 181]

5 hours ago, w6kd said:

See page 8 of the AVSIM CTD Guide, link located at right margin of home page.

Page 8??? It's confusing. There doesn't appear to be 8 pages in the CTD Guide.

[Gary1124 181]

Okay. I think I get it. Download the P3d CTD Guide. I assume it has a page 8. I will do that on my tablet at home. On my phone now. Thanks. I will check it out.

[c912039 111]

REMOVED ... Incorrect answer posted by me

Edited June 6, 2021 by c912039
incorrect answer posted

[Gary1124 181]

On 6/5/2021 at 3:58 PM, w6kd said:

See page 8 of the AVSIM CTD Guide, link located at right margin of home page.

Okay. I was confused at first and thought I needed the P3d guide. Also misled because there is much reference to fsx in the CTD area.

I downloaded the CTD guide onto my phone making it easier to refer to as I go through things. I accidentally uninstalled P3d. I wanted to just repair. This week I will also uninstall the P3d SDK. Then I will do folder and registry cleanup. Then I will reinstall. I will test fly with the Commander in the vanilla stock version. Then I will install my A2A Bonanza and test. I will install RXP and GTN and test. Then I will test one by one with my scenery mods. UTX, FTX Base, FTX NA, Global Airports, and Global buildings. If all goes well I will load FSRealWX trial version. That's temporary, I want ASN. Finally, UTL 2. If it's still working I will use Lorby and plug the airports back in and test.

I think I had either a bad or duplicated airport scenery installed because prior to that I had done a couple hours of learning flights and no CTDs. I will keep posting progress. 

I will also unclock my hardware to. That I read can cause troubles.

Edited June 7, 2021 by Gary1124

[Gary1124 181]

So, after I realized I accidentally uninstalled my P3d v4 application I uninstalled the SDH and cleared out all the empty folders. I ran a registry repair. Tonight I reinstalled P3d v4 and when I started it for initial run it pitched a lot of missing scenery tiles and set itself up as it was before. I realized I should have cleaned out the documents folders also. So I reinstalled the Orbx products and I will reinstall my A2A Bonanza and all ot it had before and see if it runs. But I will disable my addon airports and unlock my gpu and cpu and see if it crashes or not. No time today, must go to work.