September 15, 20214 yr Hi All, I have a new BBI-32 from Leo Bodnar that has arrived. I plan to make a small overhead for FS2020 that will include various toggle switches. So far I have installed the relevant software and connected a single toggle switch. All is fine except when I assign landing lights or wing lights, for example, the toggle on the simulator vibrates and clicks rapidly almost like it hasn't quite switched into position. This also happens with my Thrustmaster Airbus quadrant on the engine starters. Has anyone had the same thing or can anyone advise if I am doing something wrong please? Many thanks, Dan
September 15, 20214 yr It sounds like you may have multiple buttons and/or multiple controllers assigned to the same control and fighting each other. Check every listed control device and make sure nothing else is assigned to that function. on any of the other controllers. Bob Scott | President and CEO, AVSIM Inc ATP Gulfstream II-III-IV-V Sys1 (MSFS20+24/XPlane12+11): AMD 9800X3D, water 2x240mm, MSI MPG X670E Carbon, 64GB GSkill 6000/30, nVidia RTX4090FE Alienware AW3821DW 38" 21:9 GSync, 2x4TB Crucial T705 PCIe5 + 2x2TB Samsung 990 SSD, EVGA 1000P2 PSU, 12.9" iPad Pro Thrustmaster TCA Boeing Yoke, TCA Airbus Sidestick, Twin TCA Airbus Throttle quads, PFC Cirrus Pedals, Coolermaster HAF932 case Sys2 (P3Dv5/v4): i9-13900KS, water 2x360mm, ASUS Z790 Hero, 32GB GSkill 7800MHz CAS36, ASUS RTX4090 Samsung 55" JS8500 4K TV@60Hz, 3x 2TB WD SN850X 1x 4TB Crucial P3 M.2 NVME SSD, EVGA 1600T2 PSU Fiber link to Yamaha RX-V467 Home Theater Receiver, Polk/Klipsch 6" bookshelf speakers, Polk 12" subwoofer, 12.9" iPad Pro PFC yoke/throttle quad/pedals with custom Hall sensor retrofit, Thermaltake View 71 case, Stream Deck XL button box Sys3 (DCS/P3Dv4/ATS/ETS): AMD 7800X3D, MSI MPG X870E Carbon, Noctua NH-D15S, 64GB GSkill 6000/30, EVGA RTX3090 Alienware AW3420DW 34" 21:9 GSync, Corsair HX1000i PSU, 4TB Crucial T705 PCIe5 + 2TB Samsung 970Evo Plus, TM TCA Officer Pack, Saitek combat pedals, TM Warthog, TM RS300 FF wheel/pedals, Coolermaster HAF XB case
September 15, 20214 yr Author That makes sense. Thanks for that. I'll have a good check through and report back either way. Thanks very much Dan
September 15, 20214 yr Author Hi, The switches are still rapidly shaking. It's odd because the number two engine starter on my Thrustmaster works fine but the number one shakes (on the screen) and falls out of orientation when switched. Any ideas? Thanks Dan
September 25, 20214 yr On 9/15/2021 at 12:03 PM, concretedan said: Hi, The switches are still rapidly shaking. It's odd because the number two engine starter on my Thrustmaster works fine but the number one shakes (on the screen) and falls out of orientation when switched. Any ideas? Thanks Dan I noticed that when I bind a toggle switch to say the landing light, I have to avoid using any “toggle” function and use the landing light “on” function in the controls setup. Same goes for all other functions that have a “toggle” feature. What I think is happening is when you have something that’s bound to a “toggle” feature in the settings, when you go to flick your actual toggle switch msfs reads that physical toggle switch as a “toggling” the button, so essentially it’s like continuously hitting the button in and off (even thought your physical toggle button isn’t moving) It’s harder than I thought it would be to explain this but I hope you can make sense of what I’m trying to say. Intel I7 12700KF / 32 GB Ram-3600mhz / Windows 11 - 64 bit / NVIDIA GeForce RTX 3060TI / 32" Acer Monitor, Honeycomb alpha/bravo, CH rudder pedals, Tobii 5, Buttkicker, Logitech radio panel.
October 2, 20214 yr Author Thanks for your reply. Much appreciated. I've been on holiday for the past week so I'll try what you suggest and see if it changes. Thanks again.
Archived
This topic is now archived and is closed to further replies.