Mac1

Can the gauge be moved to a second computer?

Yes, I can see where I am ok. I have no trouble with the default 737. If I swapped the default 737 air file and configuration file and transferred to the Wilco would that work?

I've found it impossible to auto land my 737 Wilco - never catches the glide slope. But with default fsx737 it does the job every time. Is there a way that I can swap the the default guts ( the bit that makes it fly) and transfer it into my Wilco?

As I get near to the installation I get a message saying c:Fsxorbx\etc etc can not be found. As the install should be in C\FSX\ORBX what is going on? Sorry, should read. " as I get near to the installation end"

Thanks Mark, all is well now that I have PLANSTEP to on in the ini file. Interestingly although everyone says the EFIS should be set to PLN, for me it has to be set to MAP!!

Selkan Thank you for your input. The next stage is for me to go through the ini file and see if I can find something that fits the bill. Yes, I run the CDU on a separate computer. Unfortunately I get very little response from PM. I have asked Enrico to help further but he has declined. All keys on my FDS CDU are working. The next page key works when in other modes. Enrico says that according to the setting you have the NEXT PAGE will either turn the page or STEP through the individual waypoints in a flight plan. Thanks for help. I will just plod on Selkan I found it in the ini file. PlanStep = on

Yes, that is what should happen but the next page buttons do not step down for me. Enrico says it is a setting in the settings page but I can't see it!

I have Project Magenta's CDU. Where is the setting that allows me to STEP through the waypoints?

Yes it is Project Magenta

I am using PM's CDU. When I file a flight plan I can go to the LEGS page but the "NEXT PAGE" button does not turn the page. The next page flashes up for a second but stays on page one. Also how do I enable a step button so I can scroll through each waypoint?

Can anyone give me the diameter of Open Cockpits EGT gauge? Do they fit the FDS Overhead?

When I enable Vox I get a warning of fatal error and told to disable. I have a flight plan. Is there a way around this? Vox was fine until I did an fsx reinstall.

Thanks, I reached the same conclusion and am awaiting arrival of speaker/amplifyer!

I am using Vox with sound to the headphones. Is there a way to have sound also coming from a speaker in the cockpit so that visitors can hear what's going on? Martin

I am using Triplehead2go. Does wide view offer any advantages?

Are there any advantages using Wideview? I am using triple head2 go at the moment.

After loading northern Rockies I get this message. "could not complete operation, a file already exists in this path. After owing that a message says "could not finf a part of the path c:\fsx\Orbx\scripts\backup\default.XML Can anyone help?

Once again (it has happened many times in the last 10 Years) my rudder has done a full left hardover. Nothing I do will get it centered. Has anyone a solution? I am not using rudder pedals of fsuipc.

I have three Widefs keys from previous installations. Why won't any of these work?

I have the fsuipc and registered it but Widefs will not register because the key was from a previous download. Does this mean I have to repurchse fsuipc again?

I have the FDS overhead. For the last two weeks it has been dead and does not light up when the Master Switch is turned on. I am using it in conjunction with PM Systems. In PM Systems the master switch does not move although the battery switches do. PM Systems does not show the battery readings either. Help would be much appreciated.

Thanks Jim....... Martin

Is there a way of saving the sound sound devices chosen in fsx? Each time I start fsx I have to re-assign the sound device to headphones.

Is there a way of saving the sound sound devices chosen in fsx? Each time I start fsx I have to re-assign the sound device to headphones.

Where do I post questions on fsx problems