costanzo_roberto

Trans For Replay, I resolve the Problem For complete Unistall the Programm Fs2crew and Reinstall. Tanks For Your Fast Replay. Roberto.

I can not Open the Main Panel of Fs2crew Reboot to 737Ngx to Prepar3D Ver.2.5 Hotfix 4 The following Setu But Not Open. - Set configuraton Key ( N ) Menu Settings-Controls Autofeather - Configuration Manager ( Fs2Crew Enable ) - Looking File Panel.cfg : Gauge00=Fs2Crew2010\version\...... Any Idea for my Problem ?

Hi, The Scenery Aerosoft BariX working on Prepar3D ver. 2.1 ? Have a Good Day, Roberto.

Hi, If Active menu `(FAILURES / NONE) Management of Pitot tubes is in realistic mode? What happens if Active Menu `(SIMULATION / SERVICE FAILURES BASED / ON)? I would like to better understand the operation of these parameters before you have problems, Have a Good Day, Roberto.

Hi, The Pmdg 737Ngx View all Correct corrent Dc Amp of TR1, TR2, and TR3? I do not understand why the current of TR1 that give 737Ngx !!! The Normal Corrend Dc for TR1 20-25 Amp. Dc When I Move the selector of TR1, the display shows a current Very High ... Why I Find the Bus Tr1 a current greater when mano manuals Technical indicate the Max Corrent Dc Amp. 20-25 ? Have a good Day, Roberto.

Hi, In my sheet Exel does not exist a payload of the Company, I will just have to be equal to my account PayLod Panel CDU 737Ngx. Now have an error-5300Kg between my calculation from the CDU. After loading the Rynair Liveries I found many things that are inaccurate, and issuing the PMDG Liveries not go well with the actual configuration. is true 737NG has many configurations, and then the MAXTOW 74990Kg as a parameter varies for each company. The real problem exists in the PMDG program that does not load the right parameters for each company. Now I do not know if I can change configuration and weights to optimize Liveries we loaded Have a Good Day Roberto. Hi Andrea, I've Seen the parameters in the new company VirtualRynair ... also my Book Report Max Take-off 79016 kg http://www.virtualry...php/pages/fleet Ciao, Roberto.

Thanks so much for Reply, After a long search I've Seen these parameters to finish my Exel sheet where having the Fuel Plan and the payload: Configuration Liveries RYR 737-800 HDW Weigth Limitations: MAXTOW 74990Kg MALLAW 65317Kg MALTOF 70533Kg MAXZFW 61688Kg MAXLOAD 21319Kg TNKCAP 20820Kg DOW 41400Kg or 41413Kg PAYLOAD MEN 81Kg or 84Kg ? WOMAN 73Kg ?? CHILD 35Kg INFANT 00Kg BAGGAGE 13Kg or 15Kg ? Do you like these weights should be adjusted? calculating the weights is described as well as a difference of PLNZFW of 5300 kg compared to calculating the payload of the CDU 737Ngx. If I remember correctly the name you have a Very expert in PlanLoad. ciaoo, Roberto.

Hi, I'm completing a Fligth Plan with a sheet exel, but did not find in the manual PMDG 737Ngx the ( DOW ) weight in kg, which is applied in the CDU 737Ngx The page PAYLOAD and how and estimated weight to Kg, is applied to passenger? Tanks for the Repley, Have a good Day, Roberto.

Hi, solved the problem, was a dual configuration of the Gear Up Button swicth of Fsupc, which was in conflict by moving the lever to open the 737Ngx the Gear Up / GearDown during the configuration of the program 737Ngx 20 Sec. This problem can also occur if you press the button (G) and while starting the program 737Ngx. I do not understand why the programm of 737Ngx Locks all front panel keys not being setup sequence. have a Good day, Roberto.

Hi, thi my Problem to Start 737Ngx: Faulting application name: fsx.exe, version: 10.0.61637.0, time stamp: 0x46fadb14 Faulting module name: PMDG_737NGX.DLL, version: 1.0.0.0, time stamp: 0x4f5162a3 Exception code: 0xc0000005 Fault offset: 0x00016c30 Faulting process id: 0x1170 Faulting application start time: 0x01cd82c64965e4f8 Faulting application path: C:\Program Files (x86)\Microsoft Games\Microsoft Flight Simulator X\fsx.exe Faulting module path: C:\Program Files (x86)\Microsoft Games\Microsoft Flight Simulator X\GAUGES\PMDG_737NGX.DLL Report Id: d1a96acf-eeb9-11e1-ab73-f46d040ad344

Hi, The Trotthle quadrant for Pfc It works correct, and whether to open the menu `Star 737 Defalt and I make a simulation of two hours, I do not have no problem. When I configured The Axis I went and to amend Assignments for Fsx !! I do not understand when the 737Ngx Start Menu `Start, he opens up and you can see the 2D panel and the green bar that decreases with the second ... when there is no end in 5 Sec Sicroniizzation, Fsx closes and I noted Fatal Error. That controls performs the 737Ngx at that stage? have a good Day, Roberto.

Thank you for your answers, We are talking about a sistama where I installed these Addons: Windows 7 Ultimate 64 Bit - Fsx Sp2 + Acceleration Pack - 737Ngx - UTX - RexEssentiantial - Fs2crew - Gtx. hardware: Video Card = Nvidia GTX590 Cpu = I7-2600K (Sandy Briddge) Lga 1155 Quad-core ( Oc. 4,6 Ghz ) Mb. = Maximus IV Extreme Rev.B3 Chipset P67 ATX. Ram = DDR3 G.Skill Ripjaws X F3-12800CL8D-8GB (2X4GB ) CL8 SSD = Ocz 240 Gb Serie Vertex 3 Max IOPS Sata 3 3,5" I suppose an unstable problem of Oc. `cause I can not open the Far 737Ngx` Start menu? But I can only start it only after I started with the C172? I started having this problem after I installed the New Throttle Quadrant for Precicion Fligth Control ( Part #: J2E6LE-GA-STRF ) by Usb 2.0 Calibration the Axis for Fsupc. In my system Fsx only have the 737Ngx ... Thanks for your Repley, Roberto.

Hi, I have a problem with the 737NGX Sp1c, if you select from the menu `Start the 737NGX at the start when the program executes the 737NGX Setup 20 Sec. FSX Crashes and close the program FSX. In order to use the 737NGX, I Select the C172 and start FSX. when I turn off engine and Panel of C172, i select the menu for Fsx----> Aicraft----> 737NGX and everything works Well. . I have another problem with 737NGX, sometimes On Line IVAO, and only to Descend or Approach, Fsx Crashes and close the program. Maybe be the same problem or some other problem causing this error Fsx? Please help me to solve this problem. Tanks, Roberto.

Have One question for the sequence lights have found this sequence, but not be equal to that run program Fs2Crew: Landing sequences Ligth : " CLEARED TO LINE UP" EXTEND " CLEARED FOR TAKEOFF" ON " CLEARED FOR APPROACH" EXTEND " CLEARED TO LAND" ON At command to run the program Fs2Crew " RUWAY ENTRY PROCEDURE" The Landing Light Move to ( ON ) ne cause they 'do not put (on) when having the Landing Ligth have The Atc commando " CLEREAD FOR TAKEOFF" Many Times to On Line The Atc scende me The Command " LINE UP AND WAIT " Remeber The Landing Ligth have Maximun Times 5 Minut to ( On ) Have a Good Day, Roberto.

Hi, I sono to By GSX, But i Read the GSX non Works to Fs2crew For 737NGX ? The Fs2crew For 737NGX, Works Only to AES For Aerosoft ? Have a Good Day, Roberto.

Have I caused error (APU Bleed Air = Off) 1- Apu Start = On 2- Apu Bleed Air = Off 3- Call Start Engine 2 4- Fs2crew Voice Message ( no possible Start Engine 2 ) 5- Apu Bleed Air =On ( Pressure Start Engine Ok ) 6- Call Start Engine 2 ( The Sequenze non Start ) 7- Call Start Engine 1 ( The Sequenze Start and Finish ) Fs2crew non a New Step -Taxi- ReMain to Start Engine Sequenze, non message to error. Have Nice Day, Roberto.

Hi, Today or simulated an error, not inserted correctly, the APU Bleed, and I by calling (START SEQUENCE IS 2 THEN 1 ), Pushback I did while I was on the call (ENGINE START 2). Fs2crew I told the Voice that he could not do (ENGINE START 2). I put in the APU BLEED Correct way to slice a procedure ENGINE START, I did call the sequence (START ENGINE 2), in Muenu Bar of the Fs2crew, appeared the call to the correct account, but did not perform the procedure Fs2crew Start of Engine2, but has successfully executed the correct procedure (ENGINE START 1). Why not start Fs2crew ENGINE START 2 with APU BLEED exactly? Clearly not the ending sequence (START ENGINE) Fs2crew did not continue in the CECK-LIST, remaining locked in the sequence of START ENGINE. Have a Good Day, Roberto.

Hi,Thanks... I look in the manual online ... Voice of the configuration setup for Windows 7....I missed the final part of the Voice Tranning.Very Tanks For Your Help.Have Good Niigth,Roberto.

Hi,No i Not Run the Voice Tranning... how can I do to start the Voice tranning?tanks,Roberto.

Hi,I give the correct voice command ( SELECT HEADIND SELECT ) only in flight, but looking on the monitor that the program recive command ( Set ).how can I do to make the Voice command so that correct?Have Good Day,Roberto.

Thanks For the replay,My problem tthe Voice command to SELECT the HEDING selectror For the ( MCP )Trans For the replay,Roberto

Hi,I have some problem with Fs2crew, when they make on Voice command (SELECT HEADING SELECT) program to recognize (SET).What the correct voice command for set (HEADING)?Have Good Day,Roberto.