clive6354

Hello I wish to confirm, is it a requirement for PMDG aircraft to have the controllers enabled in SETTINGS-CONTROLS when setting the throttle axis or can I set the throttle axis from within FSUIPC? Clive Alexander

Thank you for your observations....I did wonder about RAPPORT I will do further reading Clive Alexander

Thank you for your reply. I have resolved the problem I am using Malwarebytes and Windows 10 Defender, In the past few days I had also installed RAPPORT which is an advanced protection for online banking. Wondering if this had any impact on my system I decided to delete and re-install Malwarebytes, Defender and RAPPORT individually in an attempt to see if I could locate which of the programs (if any) was causing the problem. I was unable to locate which program was causing the problem but after re-install of Malwarebytes, Defender and RAPPORT the problem was resolved. I also took the opportunity to add exclusions within Malwarebytes

Hello I have been using PMDG aircraft (737, 747) for several months with my current version of P3D4.1. Today, I started to load the 737 and it requested the activation code. I entered the code but it was not accepted. I also have the same problem if i try to load the 747 aircraft. Order Numbers 386805 &386804 Advice required please Clive Alexander

Hello I am trying to assign commands using Linda for use with my Hotas Warthog throttle with my PMDG737NGX aircraft P3D V4.1 The command I am having problems assigning is the command for REVERSE THRUST. I cannot locate the command inside the PMDG 737NGX module functions. Can anyone assist or advise I am sure I had assigned this command using FSUIPC using the thrust lever (pull up and back) as a switch command to assign the Thrust Reversers but somehow I have lost the command and I am struggling to remember how I had completed the processs. Clive Alexander

Thank you for your prompt response Am I correct in saying that I can select the first officer to handle all verbal coomunications? I have a slight speech impediment and the software may get very confused if my speech is not precise

Hello Will VoxATC work with Ultimate Traffic Live in P3D V4.1 ??

PROBLEM SOLVED I re-installed ENVTEX (must have replaced the textures to thier original state before I deleted them) I deleted the shaders folder again, restarted P3D and all back to normal I am now running AS16 + ASCA + ENVTEX Lesson to be learnt "delete software correctly" but a valuable learning curve for resolving a problem Thank you for your assistance

No I did not do that

Deleted the Shaders folder but no joy

a

Checked Control Panel, all appears OK It appears that the CTD happens when Active Sky is trying to intsall the weather textures. I had deleted ENVTEX I am going to try and re-install ENVTEX and see if it makes any differnce

sorry for the confusion I had used the wrong name. I have the correct version for P3dv4 installed it is build 6403

My P3D v4 CTD when I run AS16. Can anyone advise. I had been experimentining with software REX and ENVTEX and ASCA (now deleted). I have deleted Active Sky for P3Dv4 and ASCA When I re-installed AS16 and ran it the software conneted to P3D v4 and the CTD Clive Alexander

Hello I am using Hotas Warthog Throttle with B737NGX As the the throttle levers are advanced for take-off then during flight auto throttle is selected the throttle levers in a real aircraft will move in relation the the amount of engine power required but the levers on my Warthog throttle remain stationary and will not be co-rdinated, therefore, if and when return to manual throttle control how can I determine the correct position that the levers on my Wathog should be in to take manual control Is there anyway that the Warthog throttle levers can be programmed to move in relation the the amount of power requested co-ordinated with the thrust levers on the pedestal Clive Alexander

Hello I have sorted the problem. I can now continue configure the software fully

where do i find your e.mail

Is it the Linda2 .log file you require? how do I attach a file in this forum?

Thank you for your response I have dowloaded and unzipped and placed the two folders (PMDG 737 MODULE) into the modules folder in P3d v4 PMDG 737-800 NGX is in the box at the top and when I click on FSX SYNC P3D is ihighligted in orange, i think this is wrong as it should be the name of the aircraft that should be highlighted Can you advise further

Hello I am using P3d v4 and have FSUIPC v5 (registered) I have installed LINDA 3.01 (711) I am using PMDG 737 I am trying to assign actions to the switches on my Hotas Warthog Throttle (which I am unable to do using FSUIPC) Is there a video or step by step tutorial to explain how I assign a switch to carry out a command using LINDA? I have read the manual and finding the process difficult (I have missed something) Guidance and advice would be so welcome

I have watched this video file many times but the version of FSUIPC in this video is not FSUIPC 5 and version 5 does not support mouse micros which makes mapping of many buttons and swiches very difficult

Hello I am trying to set up my Thrustmaster Warthog within P3D v4 using a registered copy of FSUIPC5. I require guidance and advice on the procedure. I understand that several of the buttons and switches require macros to be setup in order for them to work but FSUIPC5 does not support the macro feature. I understand that there is a procedure to map buttons and switces without using macros but I am findind the procedure too dificult to use. Can anyone assist or guide me step by step in setting up my Thrustmaster Warthog are there any tutorials or guides for dummies? Clive Alexander

Hello I am setting up my Thrustmaster Warthog with P3D v4 and require advice on an aspect of this procedure. I have a registered copy of FSUIPC5 and intend to use this to set up the throttle & joystick for use with PMDG aircraft. To start the procedure I have read that PMDG do not like the thrust axis controllers disabled inside the control section, is this correct? if so, do I setup the thrust axis inside the controls section and assign all other settings using FSUIPC? Clive Alexander

If I purchase the Captains version will it also be able to be used with the PMDG 737 when that is released for V4 Clive Alexander

I see that FS2CREW for 777 (P3D v4) is priced at 100,000,000 Euros on the site If i am not happy with it can I get a refund ???? Clive Alexander