TobiasWalzer

Members
  • Content Count

    13
  • Joined

  • Last visited

Community Reputation

0 Neutral

Flight Sim Profile

  • Commercial Member
    No
  • Online Flight Organization Membership
    none
  • Virtual Airlines
    No

Profile Information

  • Gender
    Male
  • Location
    ETSI
  1. TobiasWalzer

    NGX tiller issues

    Is your yoke in the vc also misaligned? I had the same issue. Seemed to be a windows driver problem. After I disabled the controls in fsx / p3d and configured them under fsuipc the problem was solved.
  2. TobiasWalzer

    SDK--any way to read the cabin press and CDU?

    You are great.... Will there be a version for the 737 too? Im interested in the 2nd pc variant.
  3. TobiasWalzer

    FSUIPC mouse macros not possible in NGX P3D 2.5?

    I found the solution: I don't use mouse macros but "FSX Event Numbers". In FSUIPC I select Key Presses, press the relevant Key, select "custom control" from drop down and insert the number "FSX Event" from this list: http://aviation.allanville.com/misc/737ngx/ Afterwards I have to enter a valid parameter (trial and error): 0, 1, 2 .... For rotary switches the most left position is 0 incrementing by 1 for each right step. Hope I could help those who have similar issues. Tobi
  4. TobiasWalzer

    APU keyboard command

    I think it must work with a FSUIPC mouse macro. If you have a registered version of fsuipc you can select "key command", press the key and afterwards select Start Mouse Macro. Then click End and do the mouse steps you need (APU Start) afterwards type in a name of the macro. Go back to fsuipc and select from the dropdown the macro for the key. In case your switches on the GF panel are recognized as switches do the same steps by selecting Buttons and Switches. Good Luck.
  5. TobiasWalzer

    is my last topic not visible for others? 0 views in 3 days....

    So thanks a lot for your support. Now I know that my topics are not blocked by anyone.
  6. TobiasWalzer

    FSUIPC mouse macros not possible in NGX P3D 2.5?

    Under FSX I could program all necessary switches with FSUIPC via mouse macros. Under P3D 2.5 many of those switches are no longer pdogrammable via mouse macros. I have installed the most recent FSUIPC version. These switches are: Engine Fire Panel, Fuel Cutoff/Idle, Nose Wheel Steering Norm Alt etc... Are these no longer programmable via mouse macros or do I have a major fault in my approach? Other Buttons / Switches are still programmable: DUs Selection, A/T A/P FMC P/RST... Also the offsets for the FSX NGX do not work with FSUIPC. Any ideas/ suggestions? Thanks in advance.
  7. TobiasWalzer

    FSUIPC mouse macros not possible in NGX P3D 2.5?

    Under FSX I could program all necessary switches with FSUIPC via mouse macros. Under P3D 2.5 many of those switches are no longer pdogrammable via mouse macros. I have installed the most recent FSUIPC version. These switches are: Engine Fire Panel, Fuel Cutoff/Idle, Nose Wheel Steering Norm Alt etc... Are these no longer programmable via mouse macros or do I have a major fault in my approach? Other Buttons / Switches are still programmable: DUs Selection, A/T A/P FMC P/RST... Also the offsets for the FSX NGX do not work with FSUIPC. Any ideas/ suggestions? Thanks in advance.
  8. Under FSX I could program all necessary switches with FSUIPC via mouse macros. Under P3D 2.5 many of those switches are no longer pdogrammable via mouse macros. I have installed the most recent FSUIPC version. These switches are: Engine Fire Panel, Fuel Cutoff/Idle, Nose Wheel Steering Norm Alt etc... Are these no longer programmable via mouse macros or do I have a major fault in my approach? Other Buttons / Switches are still programmable: DUs Selection, A/T A/P FMC P/RST... Also the offsets for the FSX NGX do not work with FSUIPC. Any ideas/ suggestions? Thanks in advance.
  9. TobiasWalzer

    Prepar3d

    Thanks a lot for all your inspiring thoughts. But at the end I hoped to get some information about the way ahead. (Thanks for the link.) Could any PMDG official please give a rough estimation if the 737 NG will be released at all within the next 12 months? Thanks.
  10. TobiasWalzer

    Prepar3d

    is there anything new about the development of the 737 NG for P3D V2.X?
  11. TobiasWalzer

    Prepar3d

    is there anything new about the development of the 737 NG for P3D V2.X?
  12. TobiasWalzer

    Prepar3d

    is there anything new about the development of the 737 NG for P3D V2.X?