TobiasWalzer
Frozen-Inactivity-
Content Count
13 -
Donations
$0.00 -
Joined
-
Last visited
Content Type
Profiles
Forums
AVSIM
Media Demo
Downloads
Gallery
Blogs
Forms
Everything posted by TobiasWalzer
-
Is your yoke in the vc also misaligned? I had the same issue. Seemed to be a windows driver problem. After I disabled the controls in fsx / p3d and configured them under fsuipc the problem was solved.
-
SDK--any way to read the cabin press and CDU?
TobiasWalzer replied to Bob Scott's topic in PMDG 737NGX | 737NGXu
You are great.... Will there be a version for the 737 too? Im interested in the 2nd pc variant. -
FSUIPC mouse macros not possible in NGX P3D 2.5?
TobiasWalzer replied to TobiasWalzer's topic in PMDG 737NGX | 737NGXu
I found the solution: I don't use mouse macros but "FSX Event Numbers". In FSUIPC I select Key Presses, press the relevant Key, select "custom control" from drop down and insert the number "FSX Event" from this list: http://aviation.allanville.com/misc/737ngx/ Afterwards I have to enter a valid parameter (trial and error): 0, 1, 2 .... For rotary switches the most left position is 0 incrementing by 1 for each right step. Hope I could help those who have similar issues. Tobi -
I think it must work with a FSUIPC mouse macro. If you have a registered version of fsuipc you can select "key command", press the key and afterwards select Start Mouse Macro. Then click End and do the mouse steps you need (APU Start) afterwards type in a name of the macro. Go back to fsuipc and select from the dropdown the macro for the key. In case your switches on the GF panel are recognized as switches do the same steps by selecting Buttons and Switches. Good Luck.
-
FSUIPC mouse macros not possible in NGX P3D 2.5?
TobiasWalzer replied to TobiasWalzer's topic in PMDG 737NGX | 737NGXu
Under FSX I could program all necessary switches with FSUIPC via mouse macros. Under P3D 2.5 many of those switches are no longer pdogrammable via mouse macros. I have installed the most recent FSUIPC version. These switches are: Engine Fire Panel, Fuel Cutoff/Idle, Nose Wheel Steering Norm Alt etc... Are these no longer programmable via mouse macros or do I have a major fault in my approach? Other Buttons / Switches are still programmable: DUs Selection, A/T A/P FMC P/RST... Also the offsets for the FSX NGX do not work with FSUIPC. Any ideas/ suggestions? Thanks in advance. -
FSUIPC mouse macros not possible in NGX P3D 2.5?
TobiasWalzer replied to TobiasWalzer's topic in PMDG 737NGX | 737NGXu
Under FSX I could program all necessary switches with FSUIPC via mouse macros. Under P3D 2.5 many of those switches are no longer pdogrammable via mouse macros. I have installed the most recent FSUIPC version. These switches are: Engine Fire Panel, Fuel Cutoff/Idle, Nose Wheel Steering Norm Alt etc... Are these no longer programmable via mouse macros or do I have a major fault in my approach? Other Buttons / Switches are still programmable: DUs Selection, A/T A/P FMC P/RST... Also the offsets for the FSX NGX do not work with FSUIPC. Any ideas/ suggestions? Thanks in advance. -
Under FSX I could program all necessary switches with FSUIPC via mouse macros. Under P3D 2.5 many of those switches are no longer pdogrammable via mouse macros. I have installed the most recent FSUIPC version. These switches are: Engine Fire Panel, Fuel Cutoff/Idle, Nose Wheel Steering Norm Alt etc... Are these no longer programmable via mouse macros or do I have a major fault in my approach? Other Buttons / Switches are still programmable: DUs Selection, A/T A/P FMC P/RST... Also the offsets for the FSX NGX do not work with FSUIPC. Any ideas/ suggestions? Thanks in advance.
-
Thanks a lot for all your inspiring thoughts. But at the end I hoped to get some information about the way ahead. (Thanks for the link.) Could any PMDG official please give a rough estimation if the 737 NG will be released at all within the next 12 months? Thanks.
-
is there anything new about the development of the 737 NG for P3D V2.X?
-
is there anything new about the development of the 737 NG for P3D V2.X?
-
is there anything new about the development of the 737 NG for P3D V2.X?