I have two strange issues after SP1.1. Right after taxi, I suddenly get the three Cargo Doors Open warnings on the Annunciator Panel. I haven't touched them at at all before, and I also haven't changed or used the Maddog Standard keyboard assignment (Shift-F8) for them.The same happens somewhere during the Approach. Any idea where that could come from ?2. The 'set to A' or 'alpha' for the Ignition during the Line Up Check does not get recognized at all. 'Set to B' or 'bravo' works.Does that point to a speech recognition problem or is it a problem with SP1 ?Mike

I have two strange issues after SP1.1. Right after taxi, I suddenly get the three Cargo Doors Open warnings on the Annunciator Panel. I haven't touched them at at all before, and I also haven't changed or used the Maddog Standard keyboard assignment (Shift-F8) for them.The same happens somewhere during the Approach. Any idea where that could come from ?2. The 'set to A' or 'alpha' for the Ignition during the Line Up Check does not get recognized at all. 'Set to B' or 'bravo' works.Does that point to a speech recognition problem or is it a problem with SP1 ?Mike

Hi Mike,1. Are the cargo doors open? Check in spot view.2. If using Alpha, don't prefix it with Set to...Straight from the code, these are the accepted responses for that part of the checklist:set to aset to balphabravooffnextcheckedCheers,

Hi Bryan,yes, the cargo doors are open, happens right after the plane starts moving for taxi. I have to close them with Shift-F8 then. I have checked all my key assignment, can't find anything else related to it. Very strange.Sorry regarding the alpha, it was my problem, just my "German/English" speech recognition :-). Mike

Hi Bryan,yes, the cargo doors are open, happens right after the plane starts moving for taxi. I have to close them with Shift-F8 then. I have checked all my key assignment, can't find anything else related to it. Very strange.Sorry regarding the alpha, it was my problem, just my "German/English" speech recognition :-). Mike

Hi Mark,Regarding cargo doors: If you "start" the Pre-Flight section by clicking "Start" on the Config panel, FS2Crew will close the cargo doors for you as the time to departure nears zero. I forget the exact time.Remember: Only press 'Start' if you want to run the complete Pre-Flight events section. It's optional!

Hi Mark,Regarding cargo doors: If you "start" the Pre-Flight section by clicking "Start" on the Config panel, FS2Crew will close the cargo doors for you as the time to departure nears zero. I forget the exact time.Remember: Only press 'Start' if you want to run the complete Pre-Flight events section. It's optional!

Bryan,yes, I know, but that's not the point. The Cargo doors are closed correctly at the end of Pre-Flight. For some strange reason, they REOPEN when I start taxi, without any key commend from my side.Mike

Bryan,yes, I know, but that's not the point. The Cargo doors are closed correctly at the end of Pre-Flight. For some strange reason, they REOPEN when I start taxi, without any key commend from my side.Mike

Hmmm, are any of your Maddog doors connected to key assignments?

HiAre you using the 'start boarding' command for the cabin crew that is available when right clicking on the PA button on the overhead panel? I had cargo doors that would open after FS2Crew shut them when using this. Flew with them open for a while as couldn't figure how to close them :( If so, use the 'emergency light test' and 'prepare for takeoff' commands, just miss this one unless wanting to manually shut the cargo doors. Rich

Are you using the 'start boarding' command for the cabin crew that is available when right clicking on the PA button on the overhead panel? I had cargo doors that would open after FS2Crew shut them when using this. Flew with them open for a while as couldn't figure how to close them :( If so, use the 'emergency light test' and 'prepare for takeoff' commands, just miss this one unless wanting to manually shut the cargo doors.

Good point! DO NOT USE THE MADDOG BOARDING FUNCTIONS as they may throw FS2Crew off sequence.

Thanks, guys, exactly that was it ! So, problem solved !Mike