Sign in to follow this  
Petermuc3

Some minor issues

Recommended Posts

Hi,

there are a couple of things which I hope can be corrected.

How can I train my F/O to pronounce ADIRS correctly, she always says something like "sdirs".

With the introduction of forcing MCE to stay alive, F/O says from time to time "ok" or something similar.

If this happens during a checklist run checklist gets stopped and I have to start again.

Besides some known problems with the FSL Bus COM-dialing is unreliable; sometimes it works

correctly, sometimes F/O dials incorrectly; like I say 132.95 F/O dials 132.85 or 132.90.

I run a "runway entry procedure" (took one from Charly and modified);

F/O challenges "state runway" I say "26 left", F/O continues "setting track 026" . I did not specify this

in my flow and it doesn't make any sense. How can I get rid of that answer?

Thanks for the help

Peter

Share this post


Link to post
Share on other sites
Help AVSIM continue to serve you!
Please donate today!

7 hours ago, Petermuc3 said:

Hi,

How can I train my F/O to pronounce ADIRS correctly, she always says something like "sdirs".

 

I believe this depends on what TTS voice you're using. Some voices allow you to tweak the pronunciation. Look under "voice properties or settings"

Obviously won't have the issue with the recorded voices we ship.

 

Share this post


Link to post
Share on other sites
1 hour ago, Petermuc3 said:

Text to Speech"Thanks,

 

where would I find that? I looked under my Cereproc TTS.

Peter

 

You need to check the 32 Bit voice allows editing settings

Do not use the accessible speech panel from Windows Control panel, as that one is 64 Bit

Go to C:\Windows\SysWOW64\Speech\SpeechUX\ folder

Run "sapi.cpl" (this is the 32 bit SAPI panel"

Select the relevant folder and see whether the "settings" button is enabled.

If it is, you may be able to make adjustments, otherwise have no other idea or check with the voice maker.

 

Share this post


Link to post
Share on other sites
10 hours ago, Petermuc3 said:

Hi,

there are a couple of things which I hope can be corrected.

How can I train my F/O to pronounce ADIRS correctly, she always says something like "sdirs".

With the introduction of forcing MCE to stay alive, F/O says from time to time "ok" or something similar.

If this happens during a checklist run checklist gets stopped and I have to start again.

Besides some known problems with the FSL Bus COM-dialing is unreliable; sometimes it works

correctly, sometimes F/O dials incorrectly; like I say 132.95 F/O dials 132.85 or 132.90.

I run a "runway entry procedure" (took one from Charly and modified);

F/O challenges "state runway" I say "26 left", F/O continues "setting track 026" . I did not specify this

in my flow and it doesn't make any sense. How can I get rid of that answer?

Thanks for the help

Peter

Happy New year Peter.

Which Cereproc voice are you using and where is she stating "ADIRS"? 

You may try typing it phonetically. They sometimes come out with odd speech and require odd solutions! "A dears"?:huh:

I usually reply "Runway twenty six left". Or just "twenty six".  Otherwise I either get ignored or she gets a bit confused..(too many Martinis over Christmas!):blink:

Cheers!

 

Share this post


Link to post
Share on other sites

Happy New Year,

unfortunately the settings button is not enabled. I am using Cereproc Katherine.

That's a good idea, Charly, I will try "a dears". I have ADIRS in my checklist as well as

in the cockpit preparation flow. Maybe I had too many glasses of wine over New Year

and can't make myself understandable:blink:

Peter

Share this post


Link to post
Share on other sites

Hi,

coming back to a couple of points mentioned above.

- correct dialing of com frequencies

- flight controls check, all is fine until "rudder full right" ; aileron, elevator, "rudder full left" perfect and then nothing or just "rudder"

- speed (no reaction, sometimes pulling/pushing works, sometimes infinite dialing upwards)

- heading (sometimes works perfectly, sometimes no reaction)

- access to some flat switches

This is with the FSL Bus; I know this aircraft is a "beast" for you developers. Nevertheless I never fly the bus without MCE, it already

creates a nice flightdeck atmosphere and takes some burden away. Every even little improvement is appreciated.

 

  • Upvote 1

Share this post


Link to post
Share on other sites

Hi,

I made a video on what is already possible and as said already I love flying with my Copilot in the FSLabs Airbus.

 

  • Upvote 1

Share this post


Link to post
Share on other sites
54 minutes ago, Petermuc3 said:

Hi,

I made a video on what is already possible and as said already I love flying with my Copilot in the FSLabs Airbus.

 

Great simulator

Great airplane

Great crew coordination.

A pleasure to watch.

Thank you for sharing.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this