Jump to content
Sign in to follow this  
Louibarnes

P3D Autogen Issue

Recommended Posts

Hi, on my flightsim recently i have noticed the autogen when landing either doesnt load, or loads very slowly where i am under around 1000ft. i dont have any problems on departure autogen loads perfect on departure however on landing it seems to occur and look very unrealistic. i have seen a few forums with this error and fixes suggest locking frame rates, however doing this i lose performance and i dont really want to do this as i know my pc can handle it as its reasonably high end and was handling it fine before this week, its as if something  has just triggered it? i have seen fixes such as remove affininty masks etc. I was wondering if anyone had a clear fix, or tips in solving the problem.

thanks, Loui

Share this post


Link to post

Long story short: do not set the 'Autogen draw distance' higher than medium/high.

Edited by Simicro

- TONY -
 

 

Share this post


Link to post

High or medium depends of your rig.

Try medium to see what happens.

  • Like 1

- TONY -
 

 

Share this post


Link to post

I have tried autogen draw distance its made a slight difference however the autogen still takes ages to load and doesnt load in very far. I am currently running i5 8600k, 1060 6gb and 16gb ram. Would upgrading my graphics card to a 1070 or 1080 make a big difference? i have attached an image showing the autogen only loads a very close distance and i want to stop this as its unrealistic and i never used to have problems with this, so wondering if buying a better graphics card or  cpu would make the difference, thanks

Loui

https://imgur.com/uLeujPJ.

Share this post


Link to post

This looks normal.. and you are flying a fast airplane..

Maybe you are expecting too much from P3D..


Bert

Share this post


Link to post

Slow autogen is usually associated with the CPU being overtaxed.  Is your 8600K overclocked?  Default turbo boost is only 4.1 GHz with 5-6 cores active.

 


Bob Scott | President and CEO, AVSIM Inc
ATP Gulfstream II-III-IV-V

System1 (P3Dv5/v4): i9-13900KS @ 6.0GHz, water 2x360mm, ASUS Z790 Hero, 32GB GSkill 7800MHz CAS36, ASUS RTX4090
Samsung 55" JS8500 4K TV@30Hz,
3x 2TB WD SN850X 1x 4TB Crucial P3 M.2 NVME SSD, EVGA 1600T2 PSU, 1.2Gbps internet
Fiber link to Yamaha RX-V467 Home Theater Receiver, Polk/Klipsch 6" bookshelf speakers, Polk 12" subwoofer, 12.9" iPad Pro
PFC yoke/throttle quad/pedals with custom Hall sensor retrofit, Thermaltake View 71 case, Stream Deck XL button box

Sys2 (MSFS/XPlane): i9-10900K @ 5.1GHz, 32GB 3600/15, nVidia RTX4090FE, Alienware AW3821DW 38" 21:9 GSync, EVGA 1000P2
Thrustmaster TCA Boeing Yoke, TCA Airbus Sidestick, 2x TCA Airbus Throttle quads, PFC Cirrus Pedals, Coolermaster HAF932 case

Portable Sys3 (P3Dv4/FSX/DCS): i9-9900K @ 5.0 Ghz, Noctua NH-D15, 32GB 3200/16, EVGA RTX3090, Dell S2417DG 24" GSync
Corsair RM850x PSU, TM TCA Officer Pack, Saitek combat pedals, TM Warthog HOTAS, Coolermaster HAF XB case

Share this post


Link to post

as you see the autogen hasnt loaded atall very far and it never used to be like this. My 8600k isnt overclocked im not sure what do to when overclocking so havnt really touched it, you suggest i do?

Share this post


Link to post

If you are running P3D V4.5. this is normal behavior as best I know..


Bert

Share this post


Link to post

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  
  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
×
×
  • Create New...