Jump to content

Sign in to follow this  
DUde101

FS2crew not showing up on 787 FMC

Recommended Posts

Hi, I just purchased and downloaded the fs2crew files for the qw787 today. The installation took less than 10 seconds, and everything seemed normal. However, I cannot find the fs2crew 787 config manager anywhere on my PC, and the option to enable fs2crew is not showing up on the 787 FMC, what happened? 

Share this post


Link to post
Share on other sites

Hi, 
There  was a Read Me file in the download zip file that says there's no separate Config Manager.

You need to activate FS2Crew via the FMC as shown in the FAQs thread.

So you're not seeing this?

enable.PNG&key=8381bcbfbc048c775088a85f5

 

 

If not, when you installed FS2Crew, ensure that the FS2Crew installer auto detected the correction location of your FSX/P3D folder.

FS2Crew can't be installed any where other than the main FSX/P3D folder.

 

Share this post


Link to post
Share on other sites

Hi, thank you for your response, it turns out, I did not have the new update for QW787, as I though I did. I installed it now, and it showed up, as in the photo you provided. I clicked enable, and then save config. Is there something else that is supposed to happen afterwards? 

 

Thanks 

Share this post


Link to post
Share on other sites

You need to click Enable, then Save.

Then shut-down P3D / FSX 🙂

Then re-load P3D FSX.

You need to shutdown P3D/FSX because it's updating the panel.cfg file, and you can't write to a file when it's already loaded by the sim (hence the need to shut it down).

Cheers,

 

 

Share this post


Link to post
Share on other sites

Ok, thank you, the enable light turned amber, and the disable light turned blue, is this good so far? 

 

 

Share this post


Link to post
Share on other sites

Ok, I did everything you said, and fs2crew is enabled, however, it seems to be on button mode, how do I switch it to voice mode?

 

Thank you very much for your help! 

Share this post


Link to post
Share on other sites
Posted (edited)

1. Press SEC to open the Secondary Panel from the FS2Crew Main Panel.

2. Go to Config - Setup page on the Secondary Panel.

3. Press the Line Select Key Button beside "Interface Method: Button".  It will then change to Voice.

Your speech recognizer needs to be set to ENGLISH US, AU, UK, IN or CA.

This is all illustrated on Page 20 of the Main Ops manual.

 

Edited by byork

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
  • Donation Goals

    AVSIM's 2020 Fundraising Goal

    Donate to our annual general fundraising goal. This donation keeps our doors open and providing you service 24 x 7 x 365. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. We reset this goal every new year for the following year's goal.


    28%
    $7,075.00 of $25,000.00 Donate Now
×
×
  • Create New...