PMDG 737NGXu Lot of Cockpit not Working

[Sparkrite 194]

Ok folks, another problem, this time with PMDG 737NGXu 800 and a lot of the cockpit clickables not clickable.

I installed it into V6 using the reg.hack which I have used for other non V5 addons, over the years, so fairly ofay with it.

The problem I have is that while the aircraft loads and is live, a lot of the cockpit buttons/switches are not available and

appear just not useable. ie. the recall button/ the master caution/the panel light controls/ etc.

The same with the overhead panel, some work others don't. I'd say about 50/50.

The 'hand' just does not apper when hovering over them.

Any ideas,please?

Edited July 21, 2023 by Sparkrite

[DavidP 1,457]

Try checking VC Mipmaps in settings

[Bakern 31]

5 hours ago, DavidP said:

Try checking VC Mipmaps in settings

Had the same problem, checking VC MipMaps in settings fixed it. 🤨

Thanks for tip. 👌

 

 

Edited July 22, 2023 by Bakern

[DavidP 1,457]

13 minutes ago, Bakern said:

Had the same problem, checking VC MipMaps in settings fixed it. 🤨

Thanks for tip. 👌

 

 

It is also a problem with the Majestic Q400 for v6 as well. Glad it helped.

[Sparkrite 194]

11 hours ago, DavidP said:

Try checking VC Mipmaps in settings

Thanks David, that did the trick all working now.

 

But how I hate the fuzziness of mipmapped VCs!

I suppose there's no pleasing some people. 😄

[DavidP 1,457]

I don't have PMDG in v6,  I have  it in v5 so don't know how to make that work.

Yes, I also turn mipmap off, and did so in v6 and had the trouble with the Q400, bit that is a bug since it waa updated for v6 and will be fixed.

Sorry I can't help further

[Sparkrite 194]

1 hour ago, DavidP said:

Sorry I can't help further

No, not at all David. You have been a great help at least now I can operate the plane in V6.

It's just that it looks like as if I need to go to specsavers.😁😁

[MaDDogz 242]

16 hours ago, Sparkrite said:

It's just that it looks like as if I need to go to specsavers.😁😁

No,no. Haven’t you heard?, specsavers come to you now! 🤓 

[Ray Proudfoot 9,217]

Gents, this useful tip might be best served in the P3D Tips and Tricks subforum.

Otherwise it will soon disappear from the topics under discussion.

[Sparkrite 194]

Good idea @Ray Proudfoot maybe @DavidP will post it there, I don't want to 'rob' his valuable tip.

 

On another point, as anybody managed to get the over wing views on the 737 in V6 similar to what they were in V5+ ?

If so maybe you would share how and also the camera settings, please?

[IanHarrison 535]

On 7/22/2023 at 8:02 AM, Bakern said:

Had the same problem, checking VC MipMaps in settings fixed it. 🤨

Thanks for tip. 👌

 

 

This puzzled me for a couple of seconds, (what would I check for?), until I realised that checking in American English means "ticking" in British English.😉

[hpenet 1]

On 7/23/2023 at 12:44 PM, Sparkrite said:

Good idea @Ray Proudfoot maybe @DavidP will post it there, I don't want to 'rob' his valuable tip.

 

On another point, as anybody managed to get the over wing views on the 737 in V6 similar to what they were in V5+ ?

If so maybe you would share how and also the camera settings, please?

Hi Sparkprite,

You need to open the file "aircraft" in the PMDG folder in SimObject folder? You search for the lines [CameraDefinition.00X]. Then you just have to add +1 to the first positive  figure in InitialXyz. For example:

before InitialXyz = 1.750, 2.050, -6.000

after InitialXyz = 2.750, 2.050, -6.000

When the figure is negative, you add -1. InitialXyz = -1.750, 2.050, -6.000 ----> InitialXyz = -2.750, 2.050, -6.000

It works form me as in P3D V5.

Regards,

Hervé

[Sparkrite 194]

21 hours ago, hpenet said:

Hi Sparkprite,

You need to open the file "aircraft" in the PMDG folder in SimObject folder? You search for the lines [CameraDefinition.00X]. Then you just have to add +1 to the first positive  figure in InitialXyz. For example:

before InitialXyz = 1.750, 2.050, -6.000

after InitialXyz = 2.750, 2.050, -6.000

When the figure is negative, you add -1. InitialXyz = -1.750, 2.050, -6.000 ----> InitialXyz = -2.750, 2.050, -6.000

It works form me as in P3D V5.

Regards,

Hervé

Excellent @hpenet !

Thank you very much, that worked perfectly.