slip-stream

Thank you Sundevil56. Appreciated. 

Once 4.4 has installed do we need to reinstall Orbx scenery or does it all work off the bat?

Thanks. That’s what I’m praying for. 

Excellent information but my head hurts from trying to piece it all together. Which tweaks would serve me best in order to reduce PR texture blurries please?

i7 @ 4.5ghz 16 ram 1080ti

Forgot to add that pausing the sim has no effect whatsoever. The blurries are fixed no matter what. 

Thanks J van E. Very helpful. I’ll upgrade tonight and see if it makes any difference. It’s a shame as on XP11 the scenery is stunning but on P3D it’s like FS9

All installed now Pete. 

Read one above. 

I say just. 3 weeks ago. But had a nightmare downloading and installing Orbx scenery. 

I’ve just installed P3DV4.3 plus TE Netherlands Orbx. I’ve tried all different graphics settings (FSX user for 10 years) to try to alleviate the dreaded blurries, that are far worse than I ever suffered with FSX, incredibly. The most unusual aspect is that the blurries are evident from the very beginning which is a first for me. Running an i7 @ 4.5ghz 16 RAM and 1080ti. No matter how I adjust the sliders it makes no difference. Is this a common problem? 

Any advice received with thanks. 

When my Saitek rudders finally give up I am going back to CH, very well put together, I had a set of gameport CH rudders for years and they work fine using a gameport to usb converter, should really drag them out of the loft and try them again.

Slightly narrower than the Saitek but not anywhere near as narrow as the Thrustmaster.

My CH pedals with gameport to USB converter are still as good as the day I bought them.

Cancel last. I've just purchased the joystick controller interface board. That is perfect for my needs.

Thank you once again, especially for that link.

Many thanks. I think a cheap joystick maybe the answer. I'm assuming I can rejoin the wires from a throttle for instance. I read that the resistance must be the same as the pot in the joystick though. Not sure how I'd check that.

Hi. I have used a slide potentiometer with 3 wires. How would I now connect that to my PC so that it is recognised? Can those wires be connected to a USB connector for instance? Thanks for any info.

Explain how are you moving the eye point ? By adjusting in the camera editing dialogue.

All left hand arrows work but none on the right hand.

Ok thanks. I'll give it a go. I wondered about the default view. I couldn't see anything referencing it. I'll look in the camera edit tool.

Yes I can move forward back up down but cannot turn my head around. Bit annoying. Yes I'm in VC mode.

I only want to use a single one out of my numerical keypad. I'll try all of them tomorrow and report back.

Can I use a single key to cycle through all of my camera views? I believe you can but can't remember how? Is it just assign same key press to every camera view?

Ok I give up as I do not have a single clue what you are talking about.

I assumed that because the option was there in the edit tool to assign a keyboard command it would work.

Is there a similar USB device to a mini keyboard but mimics joystick push buttons? Perhaps that would work..

Would this work for instance? Assign the buttons.

http://www.ebay.co.uk/itm/Arcade-Fighting-Stick-Game-Controller-Joystick-Gamepad-For-USB-PC-PS3-/381571413912

Stephen. Read the first post please. Nothing to do with DHM.

On a side note. How do I install latest version?

Running OR CV1 and flyinside.

I love the DHM affects but they do not work as they should within VR. Is there anything in the pipeline to enable these effects?

For some reason I am unable to adjust via Pitch Bank or Yaw. 

Any reason why?

Hi. 

I have just tried to allocate keyboard commands to different camera views, and not Joystick. 

When I edit the cameras the keyboard command is accepted and highlighted in the key sequence box. So far, so good. 

However, when I run FSX the keyboard commands are not doing any changes. 

Any ideas?

All aircraft types selected and VC selected 

Enable live camera and ELC control both checked.