houphad

Hi,This is happening since I bought the MD-11 but never asked about it. I cannot deply spoliers if Slats/Flaps are extended. I think it is normal operation of the MD-11. Or not?Thanks,Fouad Safi

Interresting subject...I use TOPCAT instead of load manager. And I am planning to install FS PAssengers in the coming days but I will stick to TOPCAT as the manager. Which one will dominate in terms of load and fuel?regards,Fouad

Well, I run the PMDG MD-11 on FS9 and Windows 7 64 bit with UAC (User Account Control) disabled. I never ran FS9 as Admin.Just few days ago I assigned the "X" to the A/T disconnect. I did it through the PMDG menu... No issues :( Fouad

Glad you mentioned that. I'm still trying to land at LOWI Innsbruck with the LLZ/DME RWY26 approach. When I select the LLZ 26 approach on the FMC, it requires me to enter the MIN PROF. Well I tried entering numbers from 0 all the way up to 36000! None was accepted and it said OUT OF RANGE or something similar. Knowing that LOWI RWY elevation is around 1900ft, what should the MIN PROF value be? Otherwise I always have to always enter the points manually... I dont quite understand that statement or maybe I got the RNAV concept wrong. When I enter the waypoints manually for the LOWI LLZ/DME 26 approach, I enter the speed and altitude with it as well. Engage AFS (FMC SPD / NAV / PROF) and flap down gradually. So the MD-11 follows those waypoints and numbers all the way from the IAF (RTT) to RWY 26, after that I continue manual landing. Those entered waypoints with speed/alt restrictions are not RNAV? I'm following the exact approach as mentioned in the charts.Cheers,Fouad

Hello (No Name),I just tried out LHBP in FS Commander 9.0. I couldn't find any STARs for it. Not all A/Ps have stars. ATC usually gives vectors in those cases.Its a forum rule that you write your full name for next time :)Cheers,Fouad

Are you talking about the real MD-11 or the PMDG MD-11?This might be a silly thought... I never been in a cockpit before, but I doubt the presence of all that wind sound during flight. I've been in the cabin (not MD-11 though) alot of times and I did heard or noticed a very little difference in the sound between ground and flight aside from the roaring engines.Might the wind sound in the PMDG be a bit exagerated :( Fouad

Yep I guess thats it... So it was the wind making all that noise :)) Now it shut up. hahaThanks mate....

Thanks guys,Pete, Yes I tried that. Nothing changed.Barfra1995, I have FS9 so here is what I got in the sound.cfg file:[WIND_SOUND]filename=PMDGMD11_WINDflags=0viewpoint=1minimum_volume=0maximum_volume=10000minimum_rate=1.10maximum_rate=1.30minimum_speed=160maximum_speed=650The sound became louder I guess when I took off. I want to try and cancel the wind effect so shall I bring down all values to zero?Fouad

Hi,Is there a way to reduce the cockpit packs sound in the MD-11? Its too loud making it difficult to hear ATC when I fly VATSIM.FS9 and Windows 7Thanks,Fouad

Correct me if I'm wrong...I (THINK) I remember seeing it somewhere in the FMC. Maybe the To/APPR page? Try opening that page during your landing phase. I wont be on my MD-11 tonight. I'll be flying the Level-D 767 admittingly And let me know if you find it and where :( Cheers,

Cool. thanks

Thanks for the clarification...So I understand from what you said that the 'Z' triggers the A/P on the Yoke OFF which in turn dis-engages the AFS. Right? Its only an A/P disconnect. So if I press it again it just clears the warning but it will not re-engage the AFS?And there is another key for the A/T OFF on the throttle quad. Which acts similar to the above. Pressing it will disconnet the A/T, dis-engage the FMC SPEED and pressing again will not re-engage the FMC SPEED. The second press is just to clear the alarm.Am I close enough?Fouad

Hi,I'm confused between these two and I would like to clarify the following points:1- What is the difference between pressing the 'Z' on the keyboard and pressing the AUTO FLIGHT button on the center glareshield?2- Is the 'Z' for all FMC SPEED, NAV & PROF? So pressing it wil enable/disable all the 3 systems together?3- If AFS was engaged and I pressed 'Z', what should happen? I suspect that the AFS OVRD OFF 1 & 2 switches be pressed down but that doesnt happen. And being so, which button/switch on the MD-11 cockpit gets animated when I press the 'Z'?Can someone clarify this please?Thanks :)Fouad

You might want to check this out: www.fs-repaints.co.uk Its not for free though

Good to hear that :(