antalves

I installed 737 in P3d, which flied perfectly. However, a saved fly loses all settings after reopening it. I saw same thing in FSX. Is there a solution? Thanks

I didn't find how to operate that AP. Does someone knows it?? :rolleyes:

I've CaptainSim C130 for FSX. I installed it in P3D that way: copied C130 files from FSX>SimObjects>Airplanes. The plane is there, it flies, but panel is completely dead. Nothing works. Besides that copy, I also put C130 gauges from FSX into P3D gauges. Suggestions?

Well.. I did not intend to create such an uproar ... However, I understood that to fly this 737 is really hard as a "real" 737 is . I was concern about whether the saved flight could keep or not the settings. I'll check my PC, my FSX, since the opinion is that I can't lose prior settings. Thanks :rolleyes:

I think that to fly this plane is dificult: I should have classes to get some "brevet"... Chiefly if you open a saved fly, all configuratios are gone...in plain air! Is there a newbie condition so I can fly without stress? :wub:

Have a quite similar problem: after several and precious minutes of setting zilions of buttons, if I save and reopen the fly later,I must make all settings again. Is it normal?

I've missed you, boys. Hope don't happen again, for the good of all of us

That GPS, installed in C340, does not work properly, the Instructions Manual has nothing to do with it. Is there some update for this device?? Thanks

Is it possible to improve the resolution of a VC panel?.....

I'm giving up for now. I'll fly other planes. JS41 is being to me the most unfriendly plane I ever flew

Some days the engines start, some days the left one doesn't, some days the right one...I'm lost :blink:

I did everything accordingly with your teachings, but turbines enter slowly in Reverse state after landing, resulting that even with brakes, JS has an enormous delay until it stops. There is nothing about written in the manual

I read somewhere so I do not put JS as Default flight. OK. From now on I'll (try) to remember of checking everything just after opening a saved flight. OK. I'll (try) remember also to see how Condition Levers are, first of all... :blush:

The J41 does NOT save/load panel state. If you reload a saved flight, you'll need to set most stuff back up Understood If you do not monitor the EGT, the engines will catch fire Engines burned alone. That's the craziest part

I reopen it from a saved flight. If I understood well these crashes are normal, unless I begin and end a flight, is it?

I think my JS is buggy, at least it gets "crazy" if: - I close FSX and continue to fly some time later - I do'nt close FSX, put pC in SLEEP mode, after awakening it What "crazy" means? - Engines are set on fire for themselves(...) - AP is disconected - Brakes work poorly after landing ( I'll need a longer runway I'm using FSX , W7 Ultimate, 64b Some suggestions, please?

I tried the commands, that worked well. I found, however, this AP more complicated to use than other models :rolleyes: Thanks for your attention

OK, i'll make it and give a return

I really don't know how to use JS41 autopilot. I would appreciate some help!

Things are working fine now. What did I? applied Ctrl + F4, to adjust propelers

OK, I'll try once more... As one could say: commom evil is consolation :wacko:

I've read the manual. I'm starting JS41 in cold & black state. I've made all operations above. I don't know waht FS2Crew is... :rolleyes: Just in time: I'm using FSX

I don't hear message

I followed ALL the instructions contained in the tutorial (JS41Start Up Guide), but I can't accelerate and in several times, motors shutt off alone! May be my software is "broken" (??) I need some help. please

Is there, if is of your knowledge, some EMB120 high definition panel ? Thanks