I have the Imaginesim KEWR scenery, and it's wonderful, but for some reason, the default KEWR terminals are in the same place so the terminal area is completely messed up. There are planes in the default KEWR buildings. The Imaginesim stuff works fine, but I don't get why the default scenery is messing up the add-on scenery. This never happens with other scenery files. Help please!By the way, I searched online on how to fix this problem and people said to make "an exclusion zone" or SCANAFD. I tried SCAN AFD but there was no old KEWR AFCADs and I have no idea how to make an exclusion zone. So please, help! If you can make an exclusion BGL for KEWR, that would be great! Thanks in advance!I have included a picture and as you can see, there's the old gross default terminal building with what looks like a CO B767 INSIDE it.

Have you tried asking your question of their support staff?[email protected] <[email protected]>

I have the Imaginesim KEWR scenery, and it's wonderful, but for some reason, the default KEWR terminals are in the same place so the terminal area is completely messed up. There are planes in the default KEWR buildings. The Imaginesim stuff works fine, but I don't get why the default scenery is messing up the add-on scenery. This never happens with other scenery files. Help please!By the way, I searched online on how to fix this problem and people said to make "an exclusion zone" or SCANAFD. I tried SCAN AFD but there was no old KEWR AFCADs and I have no idea how to make an exclusion zone. So please, help! If you can make an exclusion BGL for KEWR, that would be great! Thanks in advance!I have included a picture and as you can see, there's the old gross default terminal building with what looks like a CO B767 INSIDE it.

Hi looks like your missing the exclude, just open the scenery.cfg file its in your main fs2004 folder with notepad scroll till you see imaginesim kewr below the aera were is says remote copy and past thisExclude=N40 42.50,W74 09.27,N40 40.26,W74 11.58,objectsFlatten.0=18.0444,N40 42.54,W74 11.79,N40 42.54,W74 09.01,N40 40.05,W74 09.01,N40 40.05,W74 11.79It should work ok make sure to save the file.Or go to imaginesim folder which is in the main flight simulator 2004 click on the folder newark then the folder config Microsoft Games\Flight Simulator 9\Imagine Simulation\KEWR Newark\config click on the file ISaKEWR4 and it should add the airport again.

Thanks for the help guys but unfortunately it's still not working...

Any other suggestions? This is frustrating... :(

Any other suggestions? This is frustrating... :(

Just uninstall and reinstall with the installer and keycode and it should put all the excludes in the proper places and it will work just fine.

Just uninstall and reinstall with the installer and keycode and it should put all the excludes in the proper places and it will work just fine.

I'll try...

It didn't work...yet again! I give up...I'll either have to revert to my old KEWR scenery or use this one with the annoying building intrusions...

It didn't work...yet again! I give up...I'll either have to revert to my old KEWR scenery or use this one with the annoying building intrusions...

If you're using vista, the scenery.cfg file being used is buried deep in documents and settings, far away from the msfs folder. Make sure your exclude is posted in that file.

If you're using vista, the scenery.cfg file being used is buried deep in documents and settings, far away from the msfs folder. Make sure your exclude is posted in that file.

Hmmm...this might be it. Thanks I'll try it.

Yay I found it! But where do I put it to activate it?

Yay I found it! But where do I put it to activate it?

You leave it where you found it. That file belongs in doc & settings and is active there. What you need to do is copy the exclude lines into the kewr entry in that scenery.cfg file.

You leave it where you found it. That file belongs in doc & settings and is active there. What you need to do is copy the exclude lines into the kewr entry in that scenery.cfg file.

<?xml version="1.0" encoding="ISO-8859-1"?><FSData version="9.0" xmlns:xsi='http://www.w3.org/2001/XMLSchema-instance' xsi:noNamespaceSchemaLocation="bglcomp.xsd" ><ExclusionRectangle latitudeMinimum="N40 42.50" latitudeMaximum="N40 40.26" longitudeMinimum="W74 09.27" longitudeMaximum="W74 11.58" excludeAllObjects = "TRUE" excludeBeaconObjects = "FALSE" excludeEffectObjects = "FALSE" excludeGenericBuildingObjects = "FALSE" excludeLibraryObjects = "FALSE" excludeTaxiwaySignObjects = "FALSE" excludeTriggerObjects = "FALSE" excludeWindsockObjects = "FALSE"/></FSData>^ Those are the exclude lines. Do I copy and paste the entire thing or only a part of it? And where do I paste it specifically under KEWR? Can it be anywhere?

No, that is not it. Somebody else already gave the exclude and flatten entry to you way back up in post #3. Just copy those lines into the bottom of the entry for kewr that you see in the scenery config.

No, that is not it. Somebody else already gave the exclude and flatten entry to you way back up in post #3. Just copy those lines into the bottom of the entry for kewr that you see in the scenery config.

Either I'm doing it completely wrong or this thing is a lost cause. I give up.