When flying at 8000' these are a few screen grabs that I took. What could be causing the blockiness around the coasts and poor texturing on the land? This in in the PNW scenery just south of CYVR. Or is this normal for 8000' (but i dont recall it looking this bad before). The 3rd shot is a shot of my settings.Sometimes I notice on 20-30min prop flights when I am on final into my destination it seems like it take a while (1 or 2 mins) for the land to generate correctly and all the textures to look "right".Maybe the settings are to high? It almost seems as if its running out of memory or something...I do have the ENB plugin running, and I yet to use the ENB which allows the external locked FPS. Can that be causing it?Thanks for any insight!

When flying at 8000' these are a few screen grabs that I took. What could be causing the blockiness around the coasts and poor texturing on the land? This in in the PNW scenery just south of CYVR. Or is this normal for 8000' (but i dont recall it looking this bad before). The 3rd shot is a shot of my settings.Sometimes I notice on 20-30min prop flights when I am on final into my destination it seems like it take a while (1 or 2 mins) for the land to generate correctly and all the textures to look "right".Maybe the settings are to high? It almost seems as if its running out of memory or something...I do have the ENB plugin running, and I yet to use the ENB which allows the external locked FPS. Can that be causing it?Thanks for any insight!

Yeh, I've been getting similar problems over the past 2-3 weeks just like that only I'm not using the ENB plugin, The mesh and textures of add-on sceneries isreally poor, It's most obvious in my Aerosoft LEIB X and LEPA X sceneries only it used to be great up until before this started, It's not the add-on themselves because I've reinstalled them.....

Did you install a new display driver lately? If so, you might have to retweak using nvidia inspector

Not that i can think of... But i will try a reconfigure in NI... The last few times flying, it did seem like my AA settings were jacked....

Mike, please let us know if you've solved the problem with re-tweaking your NI. Would help others if they are suffering the same issues.Thanks!

I checked my NI and it's still the same settings that Ryan sugested in the thread on nvidia drivers, still the blurriness continues...

Perhaps the Orbx team over at the Orbx support forum might be better equipped to help you out.

What are you setting your framerate limit to?

Try adjusting your water settings up to High 1. I had issues with that water setting you have set, using Ryans settings with the latest drivers, and autogen set at very dense got far better performance.

What are you setting your framerate limit to?

FSX: UnlimitedExternal FPS Limiter: 30Fps

When flying at 8000' these are a few screen grabs that I took. What could be causing the blockiness around the coasts and poor texturing on the land? This in in the PNW scenery just south of CYVR. Or is this normal for 8000' (but i dont recall it looking this bad before). The 3rd shot is a shot of my settings.Sometimes I notice on 20-30min prop flights when I am on final into my destination it seems like it take a while (1 or 2 mins) for the land to generate correctly and all the textures to look "right".Maybe the settings are to high? It almost seems as if its running out of memory or something...I do have the ENB plugin running, and I yet to use the ENB which allows the external locked FPS. Can that be causing it?Thanks for any insight!

Why do you use 2m mesh resolution when you not are at a airport that doesn't require it? "BIG" waste of resources in my eyes, use 10m instead. Just my thoughts. :Rolling Eyes:When flying normal around in PNW land, 10m mesh are more than enough...., you would not see any difference, only at airport's that need it.