Jump to content

Sign in to follow this  
ger

saitek calibration

Recommended Posts

Hi guys ,

 

I just bought a saitek yoke with throttles wich i m planning to install tomorrow .

Spent some time time today reading about all the install options and calibrating the different axes in fsuipc and P3D .

 

 

My question ,

 

Is is best to calibrate everything in fsuipc or in P3d , i m asking this because i m not sure when i calibrate the axes in fsuipc the 777 FBW system gets messed up.

 

Hoping someone can help me with this

 

Thanks


Best regards ,

Gérard van Veldhoven

Boeing777_Banner_Pilot.jpg

18.png

Share this post


Link to post
Share on other sites

Hi Gerard, I recommend you first try doing your setup and calibration in P3D, which from v3.0 onward has been very easy for my with my saitek pedals and thrustmaster HOTAS controllers.  I do use FSUIPC but only for converting buttons into keycommands for the PMDG FMC Options available, and to display VAS remaining.  If you're not happy with P3D controller interface, then you can try FSUIPC but I've not found that to be necessary.


Dan Downs KCRP

Share this post


Link to post
Share on other sites

Except if one require different profiles for different types of aircraft. Twins, tri, Turbos etc. Then FSUIPC is easy and marvelous. I use and always have used FSUIPC for my throttle setups and buttons and even some rotarys, if not Linda. p3D and FSX.

Share this post


Link to post
Share on other sites

I use FSX  and also the Saitek Yoke Pro. I did nothing in FSUIPC even having the full version. I used SPAD to get beter driver for Saitek with W10, but you have to reinstall the switch panel, the pedal and the instrument panel with the original drivers of Saitek. That works after very good for FSX with W10.

The radio works too if you configure correctly the PMDG radio, and I use only from Saitek the spoiler, the reverse, the trim, the brakes, the gateaway,  the ezdock camera, the pushback, or from PMDG or FSX when GSX insn't avaible, the quake is always correct and the CRS also (just for info), but with no use. Don't try the Saitek A/P, HDG, IAS, VS and ALT. it doesn't work, but use only the PMDG A/P.

You restart your PC for the planes of FSX (P3D) and Saitek works correctly.

Good Flight

Share this post


Link to post
Share on other sites

Hi all,

 

thanks for all suggestions, since i mainly will fly the pmdg planes ,i m going to try to calibrate in p3d to see if that works and like Dan said ,if this doesn't work i can allways do it in fsuipc ,

 

thanks again


Best regards ,

Gérard van Veldhoven

Boeing777_Banner_Pilot.jpg

18.png

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
  • Donation Goals

    AVSIM's 2020 Fundraising Goal

    Donate to our annual general fundraising goal. This donation keeps our doors open and providing you service 24 x 7 x 365. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. We reset this goal every new year for the following year's goal.


    34%
    $8,560.00 of $25,000.00 Donate Now
×
×
  • Create New...