October 8, 20187 yr Has this been resolved? as I am still experiencing these stutters whilst panning eg kiad nf approach was fine taxing and panning left or right to turn. Slight stutters and also moving straight ahead slight stutters, then fine again all smooth and again it starts then fine for a bit. is it scenery loading or perhaps some process running in back ground?
October 8, 20187 yr Author Did you read my last post in this thread? For me, it is almost 100% resolved, yes... Greetings, Chris AMD Ryzen 7 9800X3D, 2x32GB DDR5 6000MT/s RAM, MSI RTX 4090 Ventus 3X, Windows 11 Home, MSFS2024
October 8, 20187 yr 6 hours ago, AnkH said: Did you read my last post in this thread? For me, it is almost 100% resolved, yes... Hi i run at 25hz same issue persists.
October 9, 20187 yr Author Then: what hardware do you use besides the 4K monitor? Did you limit your FPS to 25 inside P3D? Greetings, Chris AMD Ryzen 7 9800X3D, 2x32GB DDR5 6000MT/s RAM, MSI RTX 4090 Ventus 3X, Windows 11 Home, MSFS2024
October 9, 20187 yr 3 hours ago, AnkH said: Then: what hardware do you use besides the 4K monitor? Did you limit your FPS to 25 inside P3D? I7 4790k 4.7ghz asus vi exteme mobo 2 x titans sc 6gb sli 16gb ddr3 2400mhz ram ssd x 3 h110 water cooler 850w psi corsair 25hz refresh rate unlimited FPS tripple buffer on qiestion turning off vertical sync in nvidia control panel should I keep my refresh rate At 25hz or 60hz run unlimited in game with vsync tripple buffet off? cheer Mike
October 9, 20187 yr Author For a start, I would try to leave everything in nVIDIA Control Panel or nVIDIA Inspector on default, except "use maximum performance". Then, I would try to put a limit of 25FPS inside P3D, VSYNC on, triple buffering off. This of course only if you have your refresh rate set to 25Hz. Let me know if this improves things Greetings, Chris AMD Ryzen 7 9800X3D, 2x32GB DDR5 6000MT/s RAM, MSI RTX 4090 Ventus 3X, Windows 11 Home, MSFS2024
October 9, 20187 yr 54 minutes ago, AnkH said: For a start, I would try to leave everything in nVIDIA Control Panel or nVIDIA Inspector on default, except "use maximum performance". Then, I would try to put a limit of 25FPS inside P3D, VSYNC on, triple buffering off. This of course only if you have your refresh rate set to 25Hz. Let me know if this improves things Ya that’s what the only setting I have in ncp i tried with locking FPS to 25fps seemed a little more jittery.
October 9, 20187 yr Author Did you try the Affinity Mask Tweak? If not, try once adding on top of the prepar3d.cfg those lines: [JOBSCHEDULER] AffinityMask=85 That might help as well. Just be aware that you have to modify the prepar3d.cfg with a software that keeps the coding, for example Notepad++ Greetings, Chris AMD Ryzen 7 9800X3D, 2x32GB DDR5 6000MT/s RAM, MSI RTX 4090 Ventus 3X, Windows 11 Home, MSFS2024
October 9, 20187 yr 3 hours ago, AnkH said: Did you try the Affinity Mask Tweak? If not, try once adding on top of the prepar3d.cfg those lines: [JOBSCHEDULER] AffinityMask=85 That might help as well. Just be aware that you have to modify the prepar3d.cfg with a software that keeps the coding, for example Notepad++ Will try thanks what software to use to modify coding? i don’t understand?
October 9, 20187 yr 7 minutes ago, mikeymike said: Will try thanks what software to use to modify coding? i don’t understand? You need to use an editor that preserves the character set used in some of the P3D config files. Some of the older editors, like the Notepad utility that comes with Windows, will change the character set from UCS-2 to UTF-8 when it writes them out, and P3D may not be able to read them after that. I use the free Notepad++ editor, which writes out the file using the same the character set that it read when the file was opened. Regards Bob Scott | President and CEO, AVSIM Inc ATP Gulfstream II-III-IV-V Sys1 (MSFS20+24/XPlane12+11): AMD 9800X3D, water 2x240mm, MSI MPG X670E Carbon, 64GB GSkill 6000/30, nVidia RTX4090FE Alienware AW3821DW 38" 21:9 GSync, 2x4TB Crucial T705 PCIe5 + 2x2TB Samsung 990 SSD, EVGA 1000P2 PSU, 12.9" iPad Pro Thrustmaster TCA Boeing Yoke, TCA Airbus Sidestick, Twin TCA Airbus Throttle quads, PFC Cirrus Pedals, Coolermaster HAF932 case Sys2 (P3Dv5/v4): i9-13900KS, water 2x360mm, ASUS Z790 Hero, 32GB GSkill 7800MHz CAS36, ASUS RTX4090 Samsung 55" JS8500 4K TV@60Hz, 3x 2TB WD SN850X 1x 4TB Crucial P3 M.2 NVME SSD, EVGA 1600T2 PSU Fiber link to Yamaha RX-V467 Home Theater Receiver, Polk/Klipsch 6" bookshelf speakers, Polk 12" subwoofer, 12.9" iPad Pro PFC yoke/throttle quad/pedals with custom Hall sensor retrofit, Thermaltake View 71 case, Stream Deck XL button box Sys3 (DCS/P3Dv4/ATS/ETS): AMD 7800X3D, MSI MPG X870E Carbon, Noctua NH-D15S, 64GB GSkill 6000/30, EVGA RTX3090 Alienware AW3420DW 34" 21:9 GSync, Corsair HX1000i PSU, 4TB Crucial T705 PCIe5 + 2TB Samsung 970Evo Plus, TM TCA Officer Pack, Saitek combat pedals, TM Warthog, TM RS300 FF wheel/pedals, Coolermaster HAF XB case
October 9, 20187 yr 1 hour ago, w6kd said: You need to use an editor that preserves the character set used in some of the P3D config files. Some of the older editors, like the Notepad utility that comes with Windows, will change the character set from UCS-2 to UTF-8 when it writes them out, and P3D may not be able to read them after that. I use the free Notepad++ editor, which writes out the file using the same the character set that it read when the file was opened. Regards Ok stjll confused, so me going into user app roaming data Lockheed Martin P3d cfg opening it and adding affinity mask, then saving won’t work? mike
October 9, 20187 yr 58 minutes ago, mikeymike said: Ok stjll confused, so me going into user app roaming data Lockheed Martin P3d cfg opening it and adding affinity mask, then saving won’t work? mike What they are saying is that you should download a program called "Notepad++" and use it to open your .cfg file. I would not use regular ol Notepad. Rhett 7800X3D ♣ 96 GB G.Skill Flare ♣ Gigabyte 4090 ♣ Crucial P5 Plus 2TB
October 9, 20187 yr 1 hour ago, w6kd said: You need to use an editor that preserves the character set used in some of the P3D config files. Some of the older editors, like the Notepad utility that comes with Windows, will change the character set from UCS-2 to UTF-8 when it writes them out, and P3D may not be able to read them after that. I use the free Notepad++ editor, which writes out the file using the same the character set that it read when the file was opened. Regards Ok stjll confused, so me going into user app roaming data Lockheed Martin P3d cfg opening it and adding affinity mask, then saving won’t work? mike
October 9, 20187 yr 33 minutes ago, Mace said: What they are saying is that you should download a program called "Notepad++" and use it to open your .cfg file. I would not use regular ol Notepad. Ahh ok thank you very much.
October 10, 20187 yr 33 minutes ago, Mace said: What they are saying is that you should download a program called "Notepad++" and use it to open your .cfg file. I would not use regular ol Notepad. Ahh ok thank you very much.
Archived
This topic is now archived and is closed to further replies.