October 23, 20223 yr Ever since I installed SU10, my controller options have gone completely weird. For axes, the horizontal bar either doesn't show or is stuck at some arbitrary position. When moving any of the axes, the assignment box (above the bar) flashes on and off. When in the aircaft, most things appear to work correctly - but I've had to fiddle with them to get them working again. I use FSUIPC, but this occurs even without it running. Is this a known problem? Is there a solution?
October 23, 20223 yr 2 hours ago, Adamski_NZ said: Ever since I installed SU10, my controller options have gone completely weird. For axes, the horizontal bar either doesn't show or is stuck at some arbitrary position. When moving any of the axes, the assignment box (above the bar) flashes on and off. When in the aircaft, most things appear to work correctly - but I've had to fiddle with them to get them working again. I use FSUIPC, but this occurs even without it running. Is this a known problem? Is there a solution? you are not alone mate - yesterday spent ages trying to get my axis shown as working and get the same result on my Alpha controller - and no matter how many times I try to the cockpit zooms to work on either the Alpha or the mouse - I get no action - even though the sim shows them verified All this despite a complete new setup and a new computer pS Thinks - maybe I should check the driver on the alpha ??
October 23, 20223 yr Author Did your problems start immediately after SU10 (mine did)? I have a Logitech/Saitek X56 + rudders .... and all were working quite sensibly for many months until now. Logitech don't update their drivers very often, so it won't be that (for me at least).
October 23, 20223 yr 2 hours ago, Adamski_NZ said: Did your problems start immediately after SU10 (mine did)? I have a Logitech/Saitek X56 + rudders .... and all were working quite sensibly for many months until now. Logitech don't update their drivers very often, so it won't be that (for me at least). cant really answer that because in my case - my PC went belly up before the UD10 which happened whilst I was building a new one - but it wasnt there before it Karked it - so maybe it is the fault of UD10 not only that problem But I keep getting the CTD caused by some ridiculous reason for closing it down Seems to be a massive problem that Asobo are trying to solve
October 23, 20223 yr I noticed the same problem a while ago. Not sure if it was SU 10 where it began. 5800X3D, RTX4070, 600 Watt, one or two 1440p 32" screens, 64 GB RAM, 4 TB PCle 3 NVMe, Warthog throttle, VKB NXT EVO stick, Honeycomb Alpha yoke, CH quad, 3 Logitech panels, 2 StreamDecks, Desktop Aviator Trim Panel. Crystal Light VR.
October 25, 20223 yr Not really an idea, but when it happened to me, months ago, I started to map all my controls and axis with SPAD.next. No problems any more. Every now and then, I Try my old Asobo profiles, pointless. That way I'm more or less independent of any changes and all my profiles are on my hard drive Worth a try, alternative wold be Axis and Ohs: https://axisandohs.weebly.com/ SPAD.next: https://www.spadnext.com/home.html Both have a fully working 14 days trial option. Good luck Mick PC: Gigabyte X670 Aorus Elite, AMD Ryzen 9 9900X3D, Gigabyte GeForce RTX 4080 Super Aorus Master, DDR5 G.Skill Trident Z5 Neo 2X32 GB, Corsair HX 1000, Fractal Torrent, Samsung LC32 / G7 1440P.
Archived
This topic is now archived and is closed to further replies.