alyzar

Thanks Cai I agree its a common issue, with software upgrades and OS upgrades, but i am not going to upgrade again, just to fix a cosmetic issue

I recently did a fresh install of FSX and all the bells and whistles. I am having "font Issue" within AS2012. I do have Aerosoft buses installed but the Airbus Fonts are disabled. Please see attached pic. The fonts inside the status screens are the issue. I did do a quick forum search but font is a common word Thanks

You are correct on both fronts. Its not like FS9, just found that out. i usually do have a virgin backup but of course not now. hehe

thanks, but they are scenery files not airport files

Hello All, I have finally picked up 2 new WD Black hard drives. While backing up my current FSX folders, 2 files were on corrupt. 1 - cvx4517.bgl 2 - cvx7836.bgl I am trying to find out which cab those files are in and if somebody could provide the file size of the above files. Thanks in Advance, I really don't want to spend the next several days installing everyyyything again.

Evening all, Anybody else having download issues over at flyingcarpet45? Keep receiving a 503 error all day Thanks

Hello All, iFly and FS2C latest updates installed: I'm having a new issue during descent i believe. I have inputted the correct trans lvl for the arrival airport on the descent forecast page but co will use the trans lvl based on departure. Example leave ENGM (trans lvl 4000) arrival EIDW (trans lvl 5000). Now off to purchase your new Dash product!!!!!!! Thanks Brad

Hello All, I have a first time install of VOX and when I select panel setup, it tries to initialize and I immediately receive VAPanelSelelct has stopped working, then CTD I am running WIndows 7 Prof 64bit FSX all updated. Thanks **Fixed** Had a bad aircraft.cfg Brad

Bryan, Yes I'm am letting the timer run a full 30 mins, and I believe I am following everything As far as hitting pause, yes

Hello all, After arriving at gate and co pilot says "I'm ready for shutdown" crew begin to repeat previous flows. I hear hey cpt can we board, I'm out for the walk around, were all done, load sheet etc... Windows 7 64bit, Fsx everything updated Thanks Brad

Good evening, If this patch is still floating around can somebody please email it to me. I will PM my address. Thanks in Advance Brad

I know this was an older post but I have a question concering the taxi lights. From Older post: By Opa "I found the following information from an old forum post which I had saved in my "stack of stuff".:Perhaps it will be useful - but I have never tried it myself.quoteYes, you can! As far as removing the VC from the A/C model is concerned, it is perfectly possible and actually quite simple to do, involving only a hex editor and two changes to the aircraft.mdl file.A good hex editor can be found here (Hex Workshop 4.1 - shareware but fully functional for long enough to get the job done and then some):http://www.bpsoft.com/downloads/Open the mdl file you want to edit and search for the following hex value: 0022003900In the first two occurences of that string, simply change the 39 in 0022003900 to 00. It should now look like this: 0022000000. Save the changes, OK the creation of the backup file then exit Hex Workshop to test it out in MSFS.I have found that this works on mdl files created in GMAX, FSDS, and FSDS2. It works on the default FS9 A/C, including the new vintage models. It takes two minutes at the most to complete, and if a computer moron like me can do it, then anyone can, including chimpanzees. If you decide to go this route, be sure you use your new mdl file powers for good, not evil. end quoteHope that is useful." By edetroit "To disable the VC and keep the landing lights coded in the .mdl file, use a hex editor to look for the second occurrence of 00 22 00 39 00 in the .mdl file, and change the 39 to 38 (not 00). This should kill the VC textures and keep the landing lights coded into the model visible from the 2D flight deck view. " I did replace "39" with "38" and the landing lights do show, but no taxi lights.... Is ths the trade off, no VC for no taxi lights? Thanks Brad

Trying to isolate a recent issue. I am waiting for my forum account to be approved over at A2A, has anybody had any issues with FPS decreasing about -10 at all airports? I installed this great product and seem to be now runing anywhere for 8-14 fps when i ran 24fps on avg. I cant seem to find any post about fps and 3d lights. The only other change was the latest nvidia drivers, i then went back to the previous driver. The strange thing is that I can be sitting at KLGA at night with 100% AI, and run 8-14 fps and then sit at LIMC (2am) and still only hit 8-14fps with a very quiet airport. That makes me think its not 3d lights.PaxBrad

Thanks, but noThe isd forum links are from a ftp that covers sp1 and sp2. Thanks for the responsePaxBrad

Dolf,Here is the link for ACA2005 http://aifs.pvdveen.net/index.htm.I use the program all the time to check for errors in your aircraft.cfg files.PaxBrad