ParadiseFlight

The changes to the gate labels look great! Thanks!

I see that this is fixed! Thanks!

Some airports with multiple runways have no blank line before the 2nd and following runways on the Runways tab, making it harder to find them out as scrolling through the list. Maybe it's just with add-on airports, I'm not sure. This one is for KDCA.

I'm in MSFS. I've been visiting more unfamiliar airports and finding it a challenge to find where various terminals are that are being presented to me in GSX Pro when I ask for available gates to taxi to after arrival. The behavior does not matter which level of detail I select. Even at maximum map detail level 5, the terminal letter won't display with the gate number unless I zoom to 0.06 NM (100%). Here are a couple screenshots from LFPG. Can the letter with number be displayed without needing to display any other part of the name, so "Y2" rather than "Gate Y 2" so it will fit in the circles at the lower zoom level? Would be nice to have the option to display both gate letter and number at at least 0.2 NM zoom level which still has room inside the circles. 0.2 NM zoom 0.06 NM zoom

Currently it seems one must always zoom in 100% to display letter prefixes for gates that have them. It would be helpful if the letter prefix could always be displayed with the number at any zoom level. Could an option be added to control this?

Well again it all depends where you fly. It has all the liveries for my regional airport in the U.S. I do agree it will be great to see GA added at some point, which my airport has a lot of and would greatly add to the realism of it.

They can and do beat FSLTL for what I often do, which is fly out of a smaller regional airport that has no traffic when I'm online at night, but flying a daytime route. Maybe that isn't a common need, but it works great in this case.

I am see traffic during cruise now, visible by the contrails, by my navigation display, and by Littlenavmap. In Littlenavmap the route for all these cruise flights always says it's between two airports in Europe (can't recall the exact ICAO codes at the moment), even though I'm always flying in the U.S., but they are flying near me, parallel to my route, so I'm happy with that.

This is great to hear! However I can't find this setting you mention, in v1.0.2.

Found that this is expected behavior, as mentioned in the manual. FST loads traffic one time at the start. Different than how FSLTL works, which is constantly adding new flights in real time. But not a big deal, unless you want to sit and view traffic for a while instead of departing on your own flight.

Ahh I forgot I had moved the MSFS Packages. I did a reset paths and now the correct files are found. AND now I can see you have fixed the order that the BGL files are loading, using the priority settings in MSFS. I can now see my BGL changes to the airport. Thanks!!

It's explained in the FSLTL guide: https://www.fslivetrafficliveries.com/user-guide/ Just Flight FS Traffic models - for those with Just Flight's FS Traffic installed on your machine. This setting allows you to toggle whether the FS Traffic models are given priority over the FSLTL models or not. By default FS Traffic will be below FSLTL in priority and behave like backfill in the way AIG does. If you enable this setting the role will be reversed and you will see FS Traffic's model with priority over the FSLTL version, and FSLTL will be backfill. If using this mode it is very important only the FS Traffic models are installed and the FS Traffic injection module is not active. To ensure this, we advise that only the justflight-aircraft-traffic-fleet folder be in your community folder and all other FS traffic folders be removed / disabled."

I think just about everyone is seeing the same. I recommend submitting a ticket. https://support.justflight.com/support/login

In the current version, 2.8.8, I checked the Data Sources again out of curiosity, from the same location, KROA, with my same scenery files as before, and it's not not reporting the airport BGL files now, but instead is referencing a file related to GSX Pro. And MSFS has been restarted fresh a couple times. Strange.

The new version install automatically uninstalls the old version first. I don't know if anything is preserved.