king1706

Thanks to everyone I deleted and reinstall a fresh copy of the Cessna and then ran the updates now I get all the commands back . I really appreciate all the help and assistance Kind Regards

Once I finish work today I will go home and try these options , I do appreciate everyone help Cheers

Thanks I tried shift 8 also I tried shift 8 both are not bringing the pre flight . I had deleted before all the commands from my prepar3d options as I was told they were interfering with my FSUIPC controls so I might have deleted the command shift8 is there is a way of reinstalling that . Do I have to delete the whole cessna and reinstall again or there is a quick fix before doing this step I appreciate every one help

I wonder if someone can help me I did a full clean reinstall with peepar3d V 3 upon using the Cessna 180 I bought from A2A simulation everything works perfect except I am unable to find the command for the walk around and preflight I know it's Shift F command but I am unable to find it .I tried all the F,s with no luck do I have to reinstall something or activate something Thanks

Thanks a lot it did the trick I really apreciate the help

Hi I need some help as I just bought a 9" monitor to have the GPS run on it and I can move it from my view which I have three monitors for. 1st problem the small monitor became my main menu monitor so I succeeded to change that Now I can not put my prepar 3D in full 3 monitor screen because it jumps to the forth monitor Cover a Free GPS I downloaded from one oF the members posts . I need to have still a full view on my main three monitors 24" and have the GPS separate on my new 9" monitor I have Navida latest card and I am using the multiple surrounding option on it Thanks for any input

Thanks Ron I deleted all the assignments in prepar3d nothing left and still get the flaps moving with the mixture lever very weird

I am having issues with the pitch trim controlled by saitek instrument the pitch trim works from there but also move when I move the mixture handle at the saitek quadrant throttle I am using full version of FSUIPC to control my equipments not prepar 3D anyone can help to stop trimming from the mixture handle ?

Hello Pete , I really need your help I spent almost whole Saturday and Sundays trying to set my equipments and was a great loss of time. I downloaded Spade.Next ( paid version) as I read it is the best to make your FIP works which I have 6 of those. While updating the Spade.Next it connected also the FSUIPC paid version I have for Prepared V3.2 . Once done I was unable to have the FIP to wok also my controls where all gone ( saitek Pro and Saitek quad and Saitek trim) My other equipments worked fine ( autopilot - Instrument & radio panels) everything else stopped. Now when I use my hat switch the camera goes on top of the cabin ceiling and that is it doesn't move at all. I can not see anymore the controllers. What should I do. delete everything and start to build from the beginning what is your best advise Thanks

Hi Pete Thanks for the quick reply and the link much appreciated

Hi I am seeking help as I just bought prpar3d V3.3 Iam unable to get FSUIPC for this version or I can not located , I did buy the previous version for my Prepar3d V2.5 and was working great now I am unble to update or get a new version for prepar3d V3.3 can someone direct me to where to get that software Thanks

Thanks for the advise I will look into prepar3d v3.2 I want to make sure it is compatible with my add ons EZ Dok was a pain however opus was easy install and run ,the only downside that Opus doesn't, recognize the saitek pro yoke but configuring on the keyboard numbers was very easy EZdok kept giving errors immediately so I will stick to Opus Cheers

Dear Jim First of all thank you for jumping in and trying to help me with all these data . I was about to wipe my hard drive and start from scratch but it checked latest software installed to see if that affected my sim. And yes it was the Plan G program which caused all these issues and resulted in 10 days of frustration . Once I deleted the program and done a restart everything was back to normal with no issues at all including my Saitek equipments . Reaching that resolution was not going to happen without your help at all . I do appreciate your help A quick question which one do you recommend and easy install for prepar3d V 2.5 . EZ dock or Opus I bought both programs but none worked for me I will have to spend sometime on forums to find solutions but which one you recommend as I bought both Many Thanks

yes I ran the updates and switched the USB's restart , once back pressed prepar3d icon started for 3 seconds and shutdown immediatly not sure what is going on. Wht about full c drive format and reinstall all from beginning ?

sorry forgot the computer specs windows 7 home premuim 64 bits Intel ® Core i5-4690K CPU @3.50 GHz 3.5 GHz Installed Memory(Ram) 8.00 GB NVIDA Control Panel GeForce GTX 760 Intel HD Graphics as well Thanks