Jump to content

Archived

This topic is now archived and is closed to further replies.

asanal

All goes well until Takeoff

Recommended Posts

Hi Bryan,

 

 

I am having problem with VCV,

 

"PREFLIGHT CHECKLIST" including RWY ENTRY PROC goes flawless. After takeoff VCV stops responding. Specially some of MCP commands. Starting SELECT and SET. I didn't try OH panel commandants yet>

Speech Recognition works well, I have no problem until Takeoff. (I never had any problem PMDG -747X VCV).

I uninstall and reinstall VCV. No success,

Will you please advise .

Thanks

Share this post


Link to post
Share on other sites

Are you sure you have Servicepack 1C for NGX installed and are you sure you're using Fs2Crew 1.3?

Share this post


Link to post
Share on other sites

Hi Bryan,

 

 

I am having problem with VCV,

 

"PREFLIGHT CHECKLIST" including RWY ENTRY PROC goes flawless. After takeoff VCV stops responding. Specially some of MCP commands. Starting SELECT and SET. I didn't try OH panel commandants yet>

Speech Recognition works well, I have no problem until Takeoff. (I never had any problem PMDG -747X VCV).

I uninstall and reinstall VCV. No success,

Will you please advise .

Thanks

 

Hi Ahment,

 

Are you positive you're using the correct syntax for the voice commands as described in the manual?

 

Is the command showing up in the green bar?

 

Best,

Share this post


Link to post
Share on other sites

I printed all syntax, and keep looking at before I give the command.

Interesting thing, some times, green bar does not appears at all, but FO verifies the command. This happens usually, in LANDING mode.

IN Takeoff mode I say Set headings xxx. IN bar Captain says"Pound", I say "Set Flight Level 230" FO says Heading set 78" and plane starts to turn heading 078.

 

No response for the following commands:

 

SET FLIGHT LEVELxxx

SET ALTITUDE xxxx

SET VERTICAL SPEED UP xxxx

 

All commands with bigining SELECT

Share this post


Link to post
Share on other sites

If you don't see it in the green bar, it means the speech command is not being detected.

 

Try running the Voice Training again.

 

Also check your microphone.

 

Cheers,

Share this post


Link to post
Share on other sites

1-The GOOD NEWS : Now, all VCV COMMANDS are working perfect and FO performs accordingly.

2-The BAD News: To achieve these commands , I have to give commands in FSX PAUSE mode.

3- Green bar is not appearing any longer.

 

That is strange. :LMAO:

What shall I do?

Share this post


Link to post
Share on other sites

Hi Ahmet,

 

3. Make sure DSP is pressed on the Main Panel.

 

2. I can't explain that.

 

Are you using Saved Situation files?

 

Try loading the Trike first then load the NGX.

 

Sometimes Saved Situation files cause weird issues.

 

 

Share this post


Link to post
Share on other sites

No,I don't use saved situation files.

I can't believe , how perfect VCV is working with FSX pause mode. but it is not realistic, I cannot press pause every commands issues.

I don't have any idea any longer.

 

.

Share this post


Link to post
Share on other sites

It sounds to me like your pc is overloaded with work. What programs do you have running besides FSX and Fs2Crew? And what are your pc spec.?

Share this post


Link to post
Share on other sites

I don't think the prob is his PC is overloaded, but who knows.

 

Ahmet,

 

Try deleting your FSX.CFG file (make a backup first).

 

I've never seen a situation before where the commands only work while FS is 'paused'. That's just strange.

 

Failing that, email me and I'll help you via a remote desktop.

 

 

 

 

 

Share this post


Link to post
Share on other sites

This isn't the situation whereby FS2Crew is paused when FSX is running and vice versa is it? i.e. pauses out of synch?

 

I don't get that problem after the various updates but it did occur didn't it?

Share this post


Link to post
Share on other sites

I thought about that, too, but that issue was fixed.

 

So long as he has the most current version (V1.3) he should be totally okay.

 

And it's especially weird since it only happens after takeoff...

Share this post


Link to post
Share on other sites

Bryan,

 

 

 

I just made a test flight. Some thing is totally wrong with VCV, It looks like my case is an isolated problem. I will leave it like that. MY FSX,Cfg file after Srdan Kostic (aka Word Not Allowed)

Hardware & Flight Simulator Forums Moderator tweaks and mod application is working perfect. I will hesitate to touch it again.

I will start to use Buttons Version.

Thanks for your support.

Share this post


Link to post
Share on other sites

Bryan,

 

I saw some posts regarding "System Mechanic" tool. I am using this tool. I wonder if this tool is the source of my problem.?

Did you get any response from them?

 

Regards

Share this post


Link to post
Share on other sites

Hard to say.

 

Generally speaking 'System Mechanic' (at least older versions) damages the speech recognition system.

 

You'd find that the Voice Button won't stay on and voice recognition would not work at all from the start.

 

 

You have some other strange issue.

 

Why not just make a backup copy of your FSX.CFG with all your mods on it.... and then delete the FSX.CFG file.

 

You can always revert to your backup.

 

Cheers,

Share this post


Link to post
Share on other sites

I renamed FSX,cfg as Backup. I started FSX with new cfg.file., then Blue Screen appeared .

I reload the backup FSX.Cfg file and deleted FSX.Cfg file.

Still, all going well until takeoff, then during the climb to archive clean commands I have to click pause and then I can give select VNAV,LNAV, Command A , commands.

 

Going back to Buttons Version, again,

.

Share this post


Link to post
Share on other sites

If you got a blue screen with a fresh FSX.cfg file, then there is something wrong with your computer.

 

Cheers,

Share this post


Link to post
Share on other sites

With fresh Fsx.Cfg ,before I got Blue Screen, I got "SDK Error messages warning and SP error (?)" in Fs2Crew Main Panel bar..

Today I uninstalled Fs2Crew and reinstalled. Still the same scenario. Pause gives perfect VCV.

 

I wish you test the Pause after takeoff and let see if SET, SELECT and COMMAND commands will be available.

Share this post


Link to post
Share on other sites

×
×
  • Create New...