I know there is little in the way of forum discussion re this outstanding plane however I'll ask the question anyway. I'm trying to link my what would normally be my L & R prop levers to the L & R Fuel Selector Levers in the DA 62 via FSUIPC, but it appears there are no appropriate control option available in FSUIPC. Is this possible?

 

Thanks in advance  

1 hour ago, mattdee said:

I know there is little in the way of forum discussion re this outstanding plane however I'll ask the question anyway. I'm trying to link my what would normally be my L & R prop levers to the L & R Fuel Selector Levers in the DA 62 via FSUIPC, but it appears there are no appropriate control option available in FSUIPC. Is this possible?

 

Thanks in advance  

could you not use the Throttle1 and Throttle2, I've just tried that with 2 leavers on my ch yoke.

bob

9 hours ago, onebob said:

could you not use the Throttle1 and Throttle2, I've just tried that with 2 leavers on my ch yoke.

bob

He's talking about the fuel levers, not the throttles.

This is what I use    Switched on

                                       Set Bit 1of DA62FUELLEVER:1 (LAVR)

                                       Set Bit 1of DA62FUELLEVER:2 (LAVR)

                               Switched off

                                     Clear Bit 1of DA62FUELLEVER:1 (LAVR)

                                     Clear Bit 1of DA62FUELLEVER:2 (LAVR)

Edited July 31, 20196 yr by FreeBird(Josh)

10 minutes ago, FreeBird(Josh) said:

This is what I use    Switched on

                                       Set Bit 1of DA62FUELLEVER:1 (LAVR)

                                       Set Bit 1of DA62FUELLEVER:2 (LAVR)

                               Switched off

                                     Clear Bit 1of DA62FUELLEVER:1 (LAVR)

                                     Clear Bit 1of DA62FUELLEVER:2 (LAVR)

Hello Josh, I assume those are using LUA which I'm completely unfamiliar with, but the commands that FSUIPC sees when manipulating these controls are 

  1297141 *** EVENT: Cntrl= 65962 (0x000101aa), Param= 20 (0x00000014) FUEL_SELECTOR_SET
(for left engine CROSSFEED position)

  1302141 *** EVENT: Cntrl= 65962 (0x000101aa), Param= 19 (0x00000013) FUEL_SELECTOR_SET
(for left engine ON position)

 1347797 *** EVENT: Cntrl= 65962 (0x000101aa), Param= 0 (0x00000000) FUEL_SELECTOR_SET
(for left engine OFF position) 

 1305922 *** EVENT: Cntrl= 66523 (0x000103db), Param= 20 (0x00000014) FUEL_SELECTOR_2_SET
(for right engine CROSSFEED position)

  1304703 *** EVENT: Cntrl= 66523 (0x000103db), Param= 19 (0x00000013) FUEL_SELECTOR_2_SET
(for right engine ON position)

  1349828 *** EVENT: Cntrl= 66523 (0x000103db), Param= 0 (0x00000000) FUEL_SELECTOR_2_SET
(for right engine OFF position)

Unfortunately, I can't figure out a way to assign those commands to an axis or button in FSUIPC. 

Here is the LUA with a readme I don't know much about this stuff but the files below is what you need and also a link to another post with more info and his module. Hope this helps.

https://www.dropbox.com/s/c4hqe4queu1gwx8/VERTX_DA62_LUA_CONTROLS.zip?dl=0

https://www.dropbox.com/s/4xcvl9negnz3n3b/Vertex DA62 uncommon.xml?dl=0

 

 

Edited July 31, 20196 yr by FreeBird(Josh)

58 minutes ago, FreeBird(Josh) said:

Here is the LUA with a readme I don't know much about this stuff but the files below is what you need and also a link to another post with more info and his module. Hope this helps.

https://www.dropbox.com/s/c4hqe4queu1gwx8/VERTX_DA62_LUA_CONTROLS.zip?dl=0

https://www.dropbox.com/s/4xcvl9negnz3n3b/Vertex DA62 uncommon.xml?dl=0

 

 

Thanks, that may be useful for myself as well as the OP. I'll have a look.

Edit, one more question, do you have this assigned to an axis in your setup? or to buttons?

Thanks

 

Edited July 31, 20196 yr by jalbino59
additional question

8 minutes ago, jalbino59 said:

Thanks, that may be useful for myself as well as the OP. I'll have a look.

Edit, one more question, do you have this assigned to an axis in your setup? or to buttons?

Thanks

 

To a Saitek switch panel.