May 26, 20215 yr Hi all - Is anyone else having problems with their saved controller settings getting messed up? For example, I usually set up profiles for each aircraft type for my Honeycomb yoke and throttle (multi-piston, complex single, jet, etc). I noticed after this update, all of my profiles are messed up and I have to redo all of them. For example, my single engine profile now is set with 2 throttles instead of 1. It has happened before but cannot recall if it was after an update or not. I also wonder if FSUIPC fixes this and offers saved settings for each aircraft. I was a long-time FSUIPC user in P3D and have not purchased for MSFS as of yet. If anyone has any ideas to remedy this...please share!! Eric i9-12900k, RTX 5070ti OC, 32GB ddr5 5600 RAM, 2TB 980 Pro SSD, Titan 240RX AIO, Samsung CRG90 49", Win 11
May 27, 20215 yr Hi Yes I do have a problem ..! I don't have FSUIPC for MSFS (never really had a need) My profiles are still there and appear to be working normally in the control panel but are not working at all properly in the planes. I have the Thrustmaster Hotas Warthog set and Thrustmaster rudder peddles. So far I have tried the default Caravan and the TBM with only the WT G3000 mod. The Caravan was uncontrollable via rudders and veered sharply off the runway on landing (which it never did before). The TBM's throttle shot up and remained stuck at full power, no matter what I tried to do to move it with my throttle and the rudders are more or less ineffective although they appear to be moving fine in the cockpit. Even the mouse had no effect at moving the throttle. Planes unflyable so far (after 2 days suffering trying to get the update to install... I'll have a look at the TS config panel outside MSFS in WIndows - but even MSFS does not seem to show any problems in its control panel. If you get any info on this I'd be very interested to know what to do. Thanks Ray
May 27, 20215 yr ...however, the default Crafter Club works perfectly...??? Go figure? further investigation needed..
May 27, 20215 yr My xbox controller profile always resets itself and I have no idea why. I use it to control the drone only, so I unbind everything other than the controls for that....but for some reason the profile always resets itself to the default when shutting down and reopening the sim.
May 27, 20215 yr 19 hours ago, Flic1 said: I also wonder if FSUIPC fixes this and offers saved settings for each aircraft. I was a long-time FSUIPC user in P3D and have not purchased for MSFS as of yet. If anyone has any ideas to remedy this...please share!! Yes it does. If you're a user of FSUIPC v5 or v6, it's discounted to 15 Eurogazinks. Bob Scott | President and CEO, AVSIM Inc ATP Gulfstream II-III-IV-V Sys1 (MSFS20+24/XPlane12+11): AMD 9800X3D, water 2x240mm, MSI MPG X670E Carbon, 64GB GSkill 6000/30, nVidia RTX4090FE Alienware AW3821DW 38" 21:9 GSync, 2x4TB Crucial T705 PCIe5 + 2x2TB Samsung 990 SSD, EVGA 1000P2 PSU, 12.9" iPad Pro Thrustmaster TCA Boeing Yoke, TCA Airbus Sidestick, Twin TCA Airbus Throttle quads, PFC Cirrus Pedals, Coolermaster HAF932 case Sys2 (P3Dv5/v4): i9-13900KS, water 2x360mm, ASUS Z790 Hero, 32GB GSkill 7800MHz CAS36, ASUS RTX4090 Samsung 55" JS8500 4K TV@60Hz, 3x 2TB WD SN850X 1x 4TB Crucial P3 M.2 NVME SSD, EVGA 1600T2 PSU Fiber link to Yamaha RX-V467 Home Theater Receiver, Polk/Klipsch 6" bookshelf speakers, Polk 12" subwoofer, 12.9" iPad Pro PFC yoke/throttle quad/pedals with custom Hall sensor retrofit, Thermaltake View 71 case, Stream Deck XL button box Sys3 (DCS/P3Dv4/ATS/ETS): AMD 7800X3D, MSI MPG X870E Carbon, Noctua NH-D15S, 64GB GSkill 6000/30, EVGA RTX3090 Alienware AW3420DW 34" 21:9 GSync, Corsair HX1000i PSU, 4TB Crucial T705 PCIe5 + 2TB Samsung 970Evo Plus, TM TCA Officer Pack, Saitek combat pedals, TM Warthog, TM RS300 FF wheel/pedals, Coolermaster HAF XB case
Archived
This topic is now archived and is closed to further replies.