Jas451

Running v2.0.013 over network. No problem hearing ATIS here .I see in the weather info after clicking on the info box right side of menu and clicking the weather tab.

Thanks Dave, Will wait to see if you can get it worked out. In the mean time I have no problem just ignoring the PILOT2ATC COM active setting. I would rather focus my attention in the cockpit anyway, at 65 I'm easily distracted. My preference is to run FSX at full screen so I can utilize my GTN 750 add on in a 2nd screen where it's easier for me to control.

Thanks for the replay Dave, The problem seems to vary with FSX default and add on aircraft. Some default will not allow me to switch between COM1 and 2 in PILOT2ATC, but allow the switch in FSX. In other cases default and add on aircraft will allow me to switch between COM 1and 2 in FSX, but when I change to COM1 in FSX PILOT2ATC shows COM 2 as active and when I switch to COM 2 PILOT2ATC shows COM 1 active, so if COM 2 is set to ATIS in FSX I hear the info but COM 1 is shown as active in PILOT2 ATC. I guess the solution will be for me to ignore which radio is showing active in PILOT2ATC. Am I correct in assuming that to run PILOT2ATC on the same computer as FSX that FSX has to be run in windows mode?

To any who have a network set up. I have the program running over a net work, even have ATIS playing by running a connection from headphone jack on main computer to the line in jack on network computer. The problem I have though is with the COM radios. When I have COM 1 on in FSX COM 2 is shown as active in Pilot2ATC on the network machine. When I try to change to COM 1 in PILOT2ATC to match FSX it just stays stuck on the opposite COM channel. Any ideas?

Installed the demo per instructions, load a flight plan and connect to FSX. I get a box pop up that tells me I'm connected, but when I tune to ATIS frequency shown I get an error message that say's I'm not tuned to a facility?

Yes, Thank you sir for the great fixes to this aircraft. It has made this plane a joy to fly.

Just download from the Multicrew Experience download page on the MCE site

Hi, I haven't updated MCE in awhile. Do I need to uninstall previous version or just install update over current version? :Confused:

Sorry, forgot to put the 7 in Windows. Changed folder to full control, problem solved. Thank you.

Hi, Installed Active Sky on my client pc running Windows 64 bit per network setup instructions. When I try to open Active Sky i get the following error" Your network database files could not be updated. Please make sure sharing is properly setup if using a network configuration." Tripple checked my setup and cannot find any error. All my other addons for FSX which run over a network work without any problem.

Not happy with JF just now. Bought this aircraft and tried to install. Got an "No order found" error when attempting to install. Out a good bit of money until they get this sorted out. Ok, got to change my opinion of JF. Have to assume that it was some type of order verification delay. Waited two hours and reattempted an install. Installed without any difficulty. Happy camper now. Off to see if I can get this bird in the air.

Ok, found that FSX wasn't loading my flight plan. Had to do a reinstall. Problem fixed.

Have the same problem now. After update to 6.16 no longer get response from ATC. The only response is if I do not complete a phrase then will get the "last aircraft say again" otherwise nothing. Tried setting to above normal and high, no success.

Have you contacted them through support email? Found out my problem was too many add-on aircraft. Between the aircraft installed and repaints I have over 300 aircraft config files that MCE was trying to access. Email support was able to sort out the issue, now up and running as it should, although will need to test further just to be sure no additional problems. I wish to state their support has been fantastic. Never had such good services as the folks at MCE provide.

Sorry meant PMDG 737 NGX